If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
A fatal exception 0E has occured at 0028:c02a5948
I am getting fatal exception when turning my PC off or
when restarting. Also it is running slow. Any clues? "A fatal exception 0E has occured at 0028:c02a5948 in VXD VWIN32(05) + 000012D0. The current application will be terminated. Press ..." Some time pressing CTRL+ALT+DEL will restart,otherwise I just have to use restart or power-off button. The only process that I see running (if ctrl+alt+del works) is Wmexe and Rundll32. Thanks KPS |
#2
|
|||
|
|||
A fatal exception 0E has occured at 0028:c02a5948
fatal exception OE has occurred at 0028:CO2A27A8 in VXD VWIN32(05) The current application will be terminated. A variety of problems can cause an OE at 0028, but the mention of VWin32 suggests that your problem relates to memory. I would start trouble shooting by testing the RAM, and I would test it thoroughly. You can download a test program from www.simmtester.com. You put it on a floppy disk that you boot in order to run it. It runs a cycle of several differently patterned tests over and over. You can also use RAMDrive to test the reliability of your RAM chips. However, RAMDrive can exclude no more than 32MB so it cannot test large amounts of memory. For instructions, see document Q142546 in the KnowledgeBase. If there are defects in the RAM, you will have to replace the RAM and/or its controller. This is a problem for a hardware expert . . . for example, the company that manufacturered the computer. If the RAM seems to be OK, I'd try starting Windows in Safe Mode. Although this seems unlikely to work, there's nothing lost in trying it, and if the system can run in Safe Mode, you can probably fix the problem. It is possible that your have installed a program has that messed up Windows or thatsome other event damaged Windows. Troubleshooting should follow this logic: 1. Start Win95/98 in Safe Mode. If the trouble does not appear in Safe Mode, then the trouble is caused by software conflicts or defects. Investigate each of the functions that Safe Mode turns off. 2. If the trouble also occurs in Safe Mode, rename the current Windows folder and reinstall Win95/98 into an empty folder. If the trouble does not appear with a fresh installation, the trouble is caused by something you have added to Win95/98 (but something that is not turned off by Safe Mode). 3. If the trouble occurs even with a fresh install of Windows, the trouble is arising in hardware. Safe Mode does the following: (a) bypasses config.sys and autoexec.bat (b) prevents programs from starting automatically (from win.ini or the startup folder) (c) uses standard VGA video (d) prevents a network from being started (e) disables protected mode device drivers (those listed in Device Manager) (f) bypasses the [boot] and [386Enh] sections of system.ini For more details, see document 122051 in the Microsoft KnowledgeBase. If Safe Mode makes the problem go away, you can try tests from the list below to pin down the cause of the problem. For more elaborate instructions, see document 156126 in the KnowledgeBase, which explains how to do troubleshooting in Safe Mode. With Windows 98, you can use MSConfig to help you run the tests below. With Windows 95, you can use Startup Control Panel. Startup Control Panel is similar to the Msconfig utility that ships in Windows 98. It can make troubleshooting easier by removing and restoring items from the Windows startup. You can get Startup Control Panel as freeware from: http://home.ptd.net/~don5408/toolbox/startupcpl/ Startup Cop can also disable items loading at Windows startup and it is freeware. You can download Startup Cop from: http://www.zdnet.com/downloads/stori...0,,77594,.html Yet another option is msconfig.exe as adapted to Win95: http://www2.whidbey.net/djdenham/Msconfig.htm 1. Change the video driver to Microsoft's Standard Display Adapter (VGA). Restart Windows and test. 2. Rename the Config.sys and Autoexec.bat to Config.sss and Autoexec.bbb, or edit them so that the only things loading are absolutely necessary for the computer to run. The latter items might be a SCSI driver for the harddrive, or disk management software for an EIDE drive. Deactivate EVERYTHING else by putting REM in front of that line. Reboot the computer and test. 3. Remove EVERYTHING from the Start Menu/Startup folder by dragging their icons onto the desktop. Also disable or uninstall all utilities that are running TSR (such as Norton Navigator, SoftRam or Macafee AV). Restart Windows and test. 4. Rename the Win.ini and System.ini to Win.iii and System.iii. Then make a copy of System.cb and name it System.ini. Do not rename System.cb itself. Edit the new System.ini as follows: Add device=*vmd to the [386Enh] section, and add drivers=mmsystem.dll mouse.drv=mouse.drv to the [boot] section. Restart Windows. You probably will have no mouse so you'll have to use keystrokes to do the following. Go into Device Manager and select the mouse (which will have a yellow exclamation point). Click "Remove." Again, restart Windows. Windows should find the mouse and install software for it. Test. 5. With Windows 98, run the System File Checker. Go to Start/Run and enter "sfc". 6. Rename the current Windows folder (directory). Then install Win95/98 to a new, empty folder. Test. If problem does not occur, it was caused by something in the old installation. I recommend that you keep this new installation and reinstall your Windows applications. When you reinstall applications, install Windows applications that were written for Win95/98 or WinNT but do not install older applications that were written for Windows 3.x. Install only one application at a time and test the system thoroughly before installing another application. Before you install and application, make a system snapshot with a program such as ConfigSafe; this will allow you to revert to the previous situation if (when) you install an application that causes trouble. With Win98, it is also possible to run "ScanReg /Backup" before you install an application, which allows you to restore the Registry if (when) you install an application that causes trouble. However, it is safer to make a complete system backup and recovery with ConfigSafe or a similar product. The following articles explain how to install into a new folder: How to Reinstall Windows 95 to a New Folder [142096] http://support.microsoft.com/support...s/142/0/96.asp How to Install Windows 98 to a New Folder [193902] http://support.microsoft.com/support...s/193/9/02.asp Information about reinstalling is also on www.windowsreinstall.com. Bill Starbuck (MVP) |
#3
|
|||
|
|||
A fatal exception 0E has occured at 0028:c02a5948
http://www.colba.net/~hlebo49/vwin32.htm
Leboeuf has at least this... PUB97: "Invalid VxD Dynamic Link Call" Error Message When You Click Picture Display Invalid VxD dynamic link call from VWIN32(05) +0000 119E to device "0002", service 1.Your Windows configuration is invalid. http://support.microsoft.com/?kbid=302824 (Aug. 27, 2002) http://search.support.microsoft.com/...SD=GN&LN=EN-US MSKB Search "Vwin32(05)"; All Products; Full Text; Exact Phrase; produces this additional... http://support.microsoft.com/default...b;en-us;190915 Fatal Exception 0E at 0028:c028bac6 in VXD Vwin32(05)... (190915) - When you start your computer after upgrading to Windows 98, you may receive one or more of the following error messages: Fatal Exception 0E at 0028:c028bac6 in VXD Vwin32(05)+0000281a dmistart timed out waiting for INITCOMPLETE message from c:\program... -- Thanks or Good Luck, There may be humor in this post, and, Naturally, you will not sue, should things get worse after this, PCR "KPS" wrote in message ... | I am getting fatal exception when turning my PC off or | when restarting. Also it is running slow. Any clues? | | "A fatal exception 0E has occured at 0028:c02a5948 in VXD | VWIN32(05) + 000012D0. The current application will be | terminated. Press ..." | | Some time pressing CTRL+ALT+DEL will restart,otherwise I | just have to use restart or power-off button. The only | process that I see running (if ctrl+alt+del works) is | Wmexe and Rundll32. | | Thanks | KPS |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Fatal Exception Errors | Glenn | General | 9 | September 15th 04 11:42 AM |
Fatal Exception 0E/0D errors - PLEASE HELP | Rod | General | 1 | July 3rd 04 03:10 AM |
Fatal Exception Errors | Glenn | General | 4 | June 14th 04 08:31 PM |
Cause of VxD fatal exception? | SM | Shell | 1 | June 11th 04 12:13 AM |
fatal exception OD has occured at 1F6F:00000032 | Andy | Software & Applications | 1 | May 18th 04 01:40 AM |