If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
How can I find out why COMM2 port shows invalid or busy
On Feb 8, 3:41 pm, "Jeff Richards" wrote:
The COMM2 Port is a virtual port. It is created as part of the software installation for the modem and sound card. It appears that the installation has failed, and COMM2 does not exist. You need to review the installation process and determine where it may have failed. Are you sure you are using the latest version of the drivers? Are you sure you followed the installation procedure as set out by the manufacturer? Is the machine showing any other problems that may have interfered with the installation of the software? Have you followed the advice that Mr Terhune provided last time you tried this install? -- Jeff Richards MS MVP (Windows - Shell/User)"DJW" wrote in message ... My ESS modem reports that the port is busy. How can I find out why? I formatted the hard drive on my Winbook laptop and started to do a clean install of win 98SE. I have a combination M2EM PCI (Maestro) sound card / modem made by ESS. I followed the Winbook's instructions to get the sound card and modem installed correctly. The sound card seems to work correctly but when I try to dial out with the modem using the dialer in the start menu under accessories – communications I get the message “another program is using the selected telephone device. But as far as I know that is not the case. I then installed AOL and when I try to go out to get my local access numbers it reports that the communications port is invalid or busy. The modem model is ESS ES56CVH-PI Data Fax Voice Modem. In the device manager of the system control panel under the modem listing it says that the device is working properly. Also In the device manager however under the Ports (COMM & LPT) there is only the communication port COMM1 and the printer port LTP listed. Should I also see a COMM2 listing? In the modem control panel under that modems sub listing under the General Tab shows COMM2 which is what the documentation from ESS and Windbook says the modem should use. And if I go to the diagnostic tab and select it and try to get more info I get the message couldn’t open port then I get the more info box that has port info as: Port COMM2 Interrupt 5 Address 2F8 UART is grayed out Highest speed shows no response How can I find out why the port shows invalid or busy? Ben I did you read my question I said I do not have a COMM2 listing in my device manager. I went to the modem listing in device manager where I got the resources information and tried to change the interrupt from 5 to 3. I got the message This resource setting cannot be modified. |
#12
|
|||
|
|||
How can I find out why COMM2 port shows invalid or busy
On Feb 10, 5:41 pm, DJW wrote:
On Feb 8, 3:41 pm, "Jeff Richards" wrote: The COMM2 Port is a virtual port. It is created as part of the software installation for the modem and sound card. It appears that the installation has failed, and COMM2 does not exist. You need to review the installation process and determine where it may have failed. Are you sure you are using the latest version of the drivers? Are you sure you followed the installation procedure as set out by the manufacturer? Is the machine showing any other problems that may have interfered with the installation of the software? Have you followed the advice that Mr Terhune provided last time you tried this install? -- Jeff Richards MS MVP (Windows - Shell/User)"DJW" wrote in message .... My ESS modem reports that the port is busy. How can I find out why? I formatted the hard drive on my Winbook laptop and started to do a clean install of win 98SE. I have a combination M2EM PCI (Maestro) sound card / modem made by ESS. I followed the Winbook's instructions to get the sound card and modem installed correctly. The sound card seems to work correctly but when I try to dial out with the modem using the dialer in the start menu under accessories – communications I get the message “another program is using the selected telephone device. But as far as I know that is not the case. I then installed AOL and when I try to go out to get my local access numbers it reports that the communications port is invalid or busy. The modem model is ESS ES56CVH-PI Data Fax Voice Modem. In the device manager of the system control panel under the modem listing it says that the device is working properly. Also In the device manager however under the Ports (COMM & LPT) there is only the communication port COMM1 and the printer port LTP listed. Should I also see a COMM2 listing? In the modem control panel under that modems sub listing under the General Tab shows COMM2 which is what the documentation from ESS and Windbook says the modem should use. And if I go to the diagnostic tab and select it and try to get more info I get the message couldn’t open port then I get the more info box that has port info as: Port COMM2 Interrupt 5 Address 2F8 UART is grayed out Highest speed shows no response How can I find out why the port shows invalid or busy? Ben I did you read my question I said I do not have a COMM2 listing in my device manager. I went to the modem listing in device manager where I got the resources information and tried to change the interrupt from 5 to 3. I got the message This resource setting cannot be modified. Well I have been trying to track down where I thought I read that an infrared port is a lot of times assigned to COMM2 port. My laptop indeed has an infrared port although I have never used it. I am not even sure I own a printer that also has one. Anyway I went into device manager and under network adapters I had a listing for an infrared (not sure what it ‘s exact listing name was) I opened it up and put a check mark in the box to disable in this hardware profile. I rebooted and tried the modem. IT WORKED! I now have the modem working. I had followed windbbooks installation procedures for both the installation of the sound card modem combo and the infrared port. So I am not sure why the infrared got on COMM2. I may have done the modem out of order and did the infrared port install first. Anyway the important thing is it works and I never used or think I will need the infrared port. Not sure if it was a dream or where I read it but someone out there deserves my thanks for getting me to think the infrared and the modem problem was connected. I now previously I had looked at both and both said no conflicts. I still have no listing of a COMM2 port in the device manager. Ok one last question regarding this whole thing is where did the infrared listing go under network adapters. And even though I don’t care is there a way to get it back and or assign it a new COMM port? I looked all in the device manager and don’t see one listing for any thing with infrared or IR or Ira. When it first hardware profile is made can you make others for instances where you might take a laptop to different locations where different hardware is hooked up. Or you have so much external hardware peripherals that it is impossible to have them all hooked up to a computer at once so different profiles are for different hardware configurations? If a person makes more than one profile how do you switch between the profiles and is a restart needed each time a profile is switched. If a person wants to do what ifs with hardware is it also convenient to make another profile to play around with as to not mess up the original hardware setup? Well anyway thank you to all that chimed in about this matter. |
#13
|
|||
|
|||
How can I find out why COMM2 port shows invalid or busy
On Feb 10, 5:41 pm, DJW wrote:
On Feb 8, 3:41 pm, "Jeff Richards" wrote: The COMM2 Port is a virtual port. It is created as part of the software installation for the modem and sound card. It appears that the installation has failed, and COMM2 does not exist. You need to review the installation process and determine where it may have failed. Are you sure you are using the latest version of the drivers? Are you sure you followed the installation procedure as set out by the manufacturer? Is the machine showing any other problems that may have interfered with the installation of the software? Have you followed the advice that Mr Terhune provided last time you tried this install? -- Jeff Richards MS MVP (Windows - Shell/User)"DJW" wrote in message .... My ESS modem reports that the port is busy. How can I find out why? I formatted the hard drive on my Winbook laptop and started to do a clean install of win 98SE. I have a combination M2EM PCI (Maestro) sound card / modem made by ESS. I followed the Winbook's instructions to get the sound card and modem installed correctly. The sound card seems to work correctly but when I try to dial out with the modem using the dialer in the start menu under accessories – communications I get the message “another program is using the selected telephone device. But as far as I know that is not the case. I then installed AOL and when I try to go out to get my local access numbers it reports that the communications port is invalid or busy. The modem model is ESS ES56CVH-PI Data Fax Voice Modem. In the device manager of the system control panel under the modem listing it says that the device is working properly. Also In the device manager however under the Ports (COMM & LPT) there is only the communication port COMM1 and the printer port LTP listed. Should I also see a COMM2 listing? In the modem control panel under that modems sub listing under the General Tab shows COMM2 which is what the documentation from ESS and Windbook says the modem should use. And if I go to the diagnostic tab and select it and try to get more info I get the message couldn’t open port then I get the more info box that has port info as: Port COMM2 Interrupt 5 Address 2F8 UART is grayed out Highest speed shows no response How can I find out why the port shows invalid or busy? Ben I did you read my question I said I do not have a COMM2 listing in my device manager. I went to the modem listing in device manager where I got the resources information and tried to change the interrupt from 5 to 3. I got the message This resource setting cannot be modified. Well I have been trying to track down where I thought I read that an infrared port is a lot of times assigned to COMM2 port. My laptop indeed has an infrared port although I have never used it. I am not even sure I own a printer that also has one. Anyway I went into device manager and under network adapters I had a listing for an infrared (not sure what it ‘s exact listing name was) I opened it up and put a check mark in the box to disable in this hardware profile. I rebooted and tried the modem. IT WORKED! I now have the modem working. I had followed windbbooks installation procedures for both the installation of the sound card modem combo and the infrared port. So I am not sure why the infrared got on COMM2. I may have done the modem out of order and did the infrared port install first. Anyway the important thing is it works and I never used or think I will need the infrared port. Not sure if it was a dream or where I read it but someone out there deserves my thanks for getting me to think the infrared and the modem problem was connected. I now previously I had looked at both and both said no conflicts. I still have no listing of a COMM2 port in the device manager. Ok one last question regarding this whole thing is where did the infrared listing go under network adapters. And even though I don’t care is there a way to get it back and or assign it a new COMM port? I looked all in the device manager and don’t see one listing for any thing with infrared or IR or Ira. When it first hardware profile is made can you make others for instances where you might take a laptop to different locations where different hardware is hooked up. Or you have so much external hardware peripherals that it is impossible to have them all hooked up to a computer at once so different profiles are for different hardware configurations? If a person makes more than one profile how do you switch between the profiles and is a restart needed each time a profile is switched. If a person wants to do what ifs with hardware is it also convenient to make another profile to play around with as to not mess up the original hardware setup? Well anyway thank you to all that chimed in about this matter. |
#14
|
|||
|
|||
How can I find out why COMM2 port shows invalid or busy
The infrared reference you found under networking would be the network
support for the infrared comms port. There should be no connection between this component and Comm2, but obviously there was in this case. Perhaps the network component was installed when the infrared port was at Comm2, so it had some sort of reference to it which interfered with the modem trying to use it, or perhaps it is permanently configured to refer to Comm2. There should be no particular connection between the infrared port and Comm2 other than that it is common for machines to have one physical serial port (comm1) and one infrared port( comm2). The documentation you saw may have been a warning that this 'default' connection can cause problems. It is not unusual for a virtual comms port to not appear in device manager. Note also than W98 generally does not support altering an interrupt other than by reinstalling the driver with changed parameters (and that option isn't always available). Different hardware profiles are used for different hardware configurations (for instance, a laptop plugged into a docking station) when the peripheral drivers aren't able to cope with these changes for themselves. With the introduction of the PCI bus the ability to reconfigure things on each boot meant that the need for multiple profiles pretty much disappeared, but it's useful for disabling faulty devices that insist trying to load their drivers, and for testing as you mention. However, setting up different profiles can make startup much faster when the profile matches the current hardware. See: http://support.microsoft.com/kb/236963 -- Jeff Richards MS MVP (Windows - Shell/User) "DJW" wrote in message ... On Feb 10, 5:41 pm, DJW wrote: On Feb 8, 3:41 pm, "Jeff Richards" wrote: The COMM2 Port is a virtual port. It is created as part of the software installation for the modem and sound card. It appears that the installation has failed, and COMM2 does not exist. You need to review the installation process and determine where it may have failed. Are you sure you are using the latest version of the drivers? Are you sure you followed the installation procedure as set out by the manufacturer? Is the machine showing any other problems that may have interfered with the installation of the software? Have you followed the advice that Mr Terhune provided last time you tried this install? -- Jeff Richards MS MVP (Windows - Shell/User)"DJW" wrote in message ... My ESS modem reports that the port is busy. How can I find out why? I formatted the hard drive on my Winbook laptop and started to do a clean install of win 98SE. I have a combination M2EM PCI (Maestro) sound card / modem made by ESS. I followed the Winbook's instructions to get the sound card and modem installed correctly. The sound card seems to work correctly but when I try to dial out with the modem using the dialer in the start menu under accessories – communications I get the message “another program is using the selected telephone device. But as far as I know that is not the case. I then installed AOL and when I try to go out to get my local access numbers it reports that the communications port is invalid or busy. The modem model is ESS ES56CVH-PI Data Fax Voice Modem. In the device manager of the system control panel under the modem listing it says that the device is working properly. Also In the device manager however under the Ports (COMM & LPT) there is only the communication port COMM1 and the printer port LTP listed. Should I also see a COMM2 listing? In the modem control panel under that modems sub listing under the General Tab shows COMM2 which is what the documentation from ESS and Windbook says the modem should use. And if I go to the diagnostic tab and select it and try to get more info I get the message couldn’t open port then I get the more info box that has port info as: Port COMM2 Interrupt 5 Address 2F8 UART is grayed out Highest speed shows no response How can I find out why the port shows invalid or busy? Ben I did you read my question I said I do not have a COMM2 listing in my device manager. I went to the modem listing in device manager where I got the resources information and tried to change the interrupt from 5 to 3. I got the message This resource setting cannot be modified. Well I have been trying to track down where I thought I read that an infrared port is a lot of times assigned to COMM2 port. My laptop indeed has an infrared port although I have never used it. I am not even sure I own a printer that also has one. Anyway I went into device manager and under network adapters I had a listing for an infrared (not sure what it ‘s exact listing name was) I opened it up and put a check mark in the box to disable in this hardware profile. I rebooted and tried the modem. IT WORKED! I now have the modem working. I had followed windbbooks installation procedures for both the installation of the sound card modem combo and the infrared port. So I am not sure why the infrared got on COMM2. I may have done the modem out of order and did the infrared port install first. Anyway the important thing is it works and I never used or think I will need the infrared port. Not sure if it was a dream or where I read it but someone out there deserves my thanks for getting me to think the infrared and the modem problem was connected. I now previously I had looked at both and both said no conflicts. I still have no listing of a COMM2 port in the device manager. Ok one last question regarding this whole thing is where did the infrared listing go under network adapters. And even though I don’t care is there a way to get it back and or assign it a new COMM port? I looked all in the device manager and don’t see one listing for any thing with infrared or IR or Ira. When it first hardware profile is made can you make others for instances where you might take a laptop to different locations where different hardware is hooked up. Or you have so much external hardware peripherals that it is impossible to have them all hooked up to a computer at once so different profiles are for different hardware configurations? If a person makes more than one profile how do you switch between the profiles and is a restart needed each time a profile is switched. If a person wants to do what ifs with hardware is it also convenient to make another profile to play around with as to not mess up the original hardware setup? Well anyway thank you to all that chimed in about this matter. |
#15
|
|||
|
|||
How can I find out why COMM2 port shows invalid or busy
The infrared reference you found under networking would be the network
support for the infrared comms port. There should be no connection between this component and Comm2, but obviously there was in this case. Perhaps the network component was installed when the infrared port was at Comm2, so it had some sort of reference to it which interfered with the modem trying to use it, or perhaps it is permanently configured to refer to Comm2. There should be no particular connection between the infrared port and Comm2 other than that it is common for machines to have one physical serial port (comm1) and one infrared port( comm2). The documentation you saw may have been a warning that this 'default' connection can cause problems. It is not unusual for a virtual comms port to not appear in device manager. Note also than W98 generally does not support altering an interrupt other than by reinstalling the driver with changed parameters (and that option isn't always available). Different hardware profiles are used for different hardware configurations (for instance, a laptop plugged into a docking station) when the peripheral drivers aren't able to cope with these changes for themselves. With the introduction of the PCI bus the ability to reconfigure things on each boot meant that the need for multiple profiles pretty much disappeared, but it's useful for disabling faulty devices that insist trying to load their drivers, and for testing as you mention. However, setting up different profiles can make startup much faster when the profile matches the current hardware. See: http://support.microsoft.com/kb/236963 -- Jeff Richards MS MVP (Windows - Shell/User) "DJW" wrote in message ... On Feb 10, 5:41 pm, DJW wrote: On Feb 8, 3:41 pm, "Jeff Richards" wrote: The COMM2 Port is a virtual port. It is created as part of the software installation for the modem and sound card. It appears that the installation has failed, and COMM2 does not exist. You need to review the installation process and determine where it may have failed. Are you sure you are using the latest version of the drivers? Are you sure you followed the installation procedure as set out by the manufacturer? Is the machine showing any other problems that may have interfered with the installation of the software? Have you followed the advice that Mr Terhune provided last time you tried this install? -- Jeff Richards MS MVP (Windows - Shell/User)"DJW" wrote in message ... My ESS modem reports that the port is busy. How can I find out why? I formatted the hard drive on my Winbook laptop and started to do a clean install of win 98SE. I have a combination M2EM PCI (Maestro) sound card / modem made by ESS. I followed the Winbook's instructions to get the sound card and modem installed correctly. The sound card seems to work correctly but when I try to dial out with the modem using the dialer in the start menu under accessories – communications I get the message “another program is using the selected telephone device. But as far as I know that is not the case. I then installed AOL and when I try to go out to get my local access numbers it reports that the communications port is invalid or busy. The modem model is ESS ES56CVH-PI Data Fax Voice Modem. In the device manager of the system control panel under the modem listing it says that the device is working properly. Also In the device manager however under the Ports (COMM & LPT) there is only the communication port COMM1 and the printer port LTP listed. Should I also see a COMM2 listing? In the modem control panel under that modems sub listing under the General Tab shows COMM2 which is what the documentation from ESS and Windbook says the modem should use. And if I go to the diagnostic tab and select it and try to get more info I get the message couldn’t open port then I get the more info box that has port info as: Port COMM2 Interrupt 5 Address 2F8 UART is grayed out Highest speed shows no response How can I find out why the port shows invalid or busy? Ben I did you read my question I said I do not have a COMM2 listing in my device manager. I went to the modem listing in device manager where I got the resources information and tried to change the interrupt from 5 to 3. I got the message This resource setting cannot be modified. Well I have been trying to track down where I thought I read that an infrared port is a lot of times assigned to COMM2 port. My laptop indeed has an infrared port although I have never used it. I am not even sure I own a printer that also has one. Anyway I went into device manager and under network adapters I had a listing for an infrared (not sure what it ‘s exact listing name was) I opened it up and put a check mark in the box to disable in this hardware profile. I rebooted and tried the modem. IT WORKED! I now have the modem working. I had followed windbbooks installation procedures for both the installation of the sound card modem combo and the infrared port. So I am not sure why the infrared got on COMM2. I may have done the modem out of order and did the infrared port install first. Anyway the important thing is it works and I never used or think I will need the infrared port. Not sure if it was a dream or where I read it but someone out there deserves my thanks for getting me to think the infrared and the modem problem was connected. I now previously I had looked at both and both said no conflicts. I still have no listing of a COMM2 port in the device manager. Ok one last question regarding this whole thing is where did the infrared listing go under network adapters. And even though I don’t care is there a way to get it back and or assign it a new COMM port? I looked all in the device manager and don’t see one listing for any thing with infrared or IR or Ira. When it first hardware profile is made can you make others for instances where you might take a laptop to different locations where different hardware is hooked up. Or you have so much external hardware peripherals that it is impossible to have them all hooked up to a computer at once so different profiles are for different hardware configurations? If a person makes more than one profile how do you switch between the profiles and is a restart needed each time a profile is switched. If a person wants to do what ifs with hardware is it also convenient to make another profile to play around with as to not mess up the original hardware setup? Well anyway thank you to all that chimed in about this matter. |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
fdisk shows one size and my computer shows another | icccapital | Disk Drives | 0 | July 23rd 06 02:07 PM |
BOOTED PC W/ CAMERA PLUGGED INTO USB PORT-Invalid System Disk Err | Dell | General | 1 | March 19th 06 10:31 AM |
Comm port invalid or busy | [email protected] | General | 1 | May 3rd 05 01:31 AM |
"system is busy" | Jim | General | 0 | July 5th 04 09:47 PM |
Communication port is invalid or busy | [email protected] | Hardware | 1 | June 22nd 04 07:40 PM |