A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows 98 » Setup & Installation
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

need to install Advanced Power Management - please help



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #7  
Old November 12th 04, 06:51 AM
Adam
external usenet poster
 
Posts: n/a
Default


I'm using VIA's 4-in-1 (v4.37) drivers.

I just tried the Add New Hardware wizard:
- auto hardware detection did not find any new hardware
- manual "system device" selection method did not list
"Advanced Power Management support"

Also, the Asus A7V133 User's Manual says the following:
"IMPORTANT: Advanced Power Management (APM) should be
installed to keep the system time updated when the computer
enters suspend mode activated by the BIOS Power Management.
For DOS environments, you need to add the statement,
DEVICE=C:\DOS\POWER.EXE, to your CONFIG.SYS file.
For Windows 3.x and Windows 95, you need to install Windows
with the APM feature. For Windows 98 and later, APM is
automatically installed. A battery and power cord icon labeled
"Power Management" will appear in the "Control Panel." Choose
"Advanced" in the Power Management Properties dialog box."

So, apparently, APM is already installed in my case but
there is no listing of "Advanced Power Management support" under
"System devices" in "Device Manager".

Also, comparing the Power Management Properties dialog of
the two HDD/partition, I noticed that the "Advanced" tab is missing
the "Prompt for password when computer goes off standby" checkbox.
And, the "Power Schemes" tab is missing the "System standby" dropdown list in
the "Settings for Always On power scheme" section.

Is it possible that installing standby-related stuff may trigger
the addition of "Advanced Power Management support" under
"System devices" in "Device Manager".



"glee" wrote in message ...
The procedure for adding Advanced Power Management support in Device Manager is to
use the Add New Hardware wizard to search for new hardware, and if it detects APM
support, to allow it to install, and then reboot. However, you may not be able to
detect it without installing the drivers on motherboard disc. What VIA drivers
version number did you install? Have you tried other versions from the VIA support
web site?
--
Glen Ventura, MS MVP W95/98 Systems
http://dts-l.org/goodpost.htm


"Adam" wrote in message
om...

My responses are inline ...


"Shepİ" wrote in message

...
On Thu, 11 Nov 2004 22:54:50 GMT It was a dark and stormy night when
"Spamotomy" wrote :


Okay, I think I'm a little confused ...

Must I have ACPI in order to have "Advanced Power Management support" ?
In the "good" HDD/partition, there is no mention of ACPI under
"System devices" but there is an "Advanced Power Management support" item,
which is what I'm trying to replicate on the other HDD/partition

You have mis-quoted.


Mis-quoted? No, "Advanced Power Management support" is
an item under "System devices" in "Device Manager".



For ACPI to function correctly all hardware devices on the system must
be ACPI compliant including the mother board.

Their correct drivers must be correctly installed and the Windows

Software ACPI must be installed e.g the Advanced Power Management
Support as you post above.


"Advanced Power Management support" is what I'm trying to
find out how to install without depending on hardware detection since
all the hardware is already there.



If the option is there in the BIOS to enable/disable
ACPI it must be enabled.Many Modern systems either have it hidden and
set by default to,"On".


Hmmm ... will I be able to enable ACPI without getting ACPI BIOS?
If not, then I will be "back to square one" like you said.
And, I don't want that.



You may also need to re-install motherboard/mother board chip set
drivers pack/s.


Oh-no, trying to install VIA's 4-in-1 drivers caused the dreaded message:
"Windows protection error. You need to restart your computer."
After which, I can only boot into Safe mode but not into Normal mode.


As for talk of,"Partitions" you are now confusing me :/


I use the BIOS to select the HDD (and thus, the boot partition) used for
the boot process. By "HDD/partition", I mean the HDD (and thus,
the boot partition) used to boot the system.



--
Free Windows/PC help,
http://www.geocities.com/sheppola/trouble.html
remove obvious to reply
email
Free original songs to download and,"BURN" :O)
http://www.soundclick.com/bands/8/nomessiahsmusic.htm





 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
need to install Advanced Power Management - please help Adam General 27 November 14th 04 01:12 AM
Error message: Advanced INF Install Error Message: Avanced INF Install General 2 October 2nd 04 01:48 PM
Power Management jdubya Improving Performance 0 July 19th 04 12:18 AM
Please help! Display settings !! Mitzi Monitors & Displays 12 July 11th 04 05:19 AM
Advanced Power Management John Improving Performance 1 May 24th 04 07:44 PM


All times are GMT +1. The time now is 07:29 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright İ2004-2024 Win98banter.
The comments are property of their posters.