If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ISP can no configure windows 98 for internet
Can no configure windows 98 for internet. PC was configured for small LAN,
internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks |
#2
|
|||
|
|||
ISP can no configure windows 98 for internet
mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. |
#3
|
|||
|
|||
ISP can no configure windows 98 for internet
mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. |
#4
|
|||
|
|||
ISP can no configure windows 98 for internet
Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral |
#5
|
|||
|
|||
ISP can no configure windows 98 for internet
Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral |
#6
|
|||
|
|||
ISP can no configure windows 98 for internet
"mistral" wrote in message ... Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral uncheck the "Automatically detect settings" and give it a try |
#7
|
|||
|
|||
ISP can no configure windows 98 for internet
"mistral" wrote in message ... Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral uncheck the "Automatically detect settings" and give it a try |
#8
|
|||
|
|||
ISP can no configure windows 98 for internet
Haggis wrote in message ... "mistral" wrote in message ... Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral uncheck the "Automatically detect settings" and give it a try I tried - not help. Just show message in status bar, with correct IP: 'Connecting to site: IP .. ..", or 'Opening page http://www.domain.com/ (if i type url in browser window) But no page loads. |
#9
|
|||
|
|||
ISP can no configure windows 98 for internet
Haggis wrote in message ... "mistral" wrote in message ... Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral uncheck the "Automatically detect settings" and give it a try I tried - not help. Just show message in status bar, with correct IP: 'Connecting to site: IP .. ..", or 'Opening page http://www.domain.com/ (if i type url in browser window) But no page loads. |
#10
|
|||
|
|||
ISP can no configure windows 98 for internet
"mistral" wrote in message ... Haggis wrote in message ... "mistral" wrote in message ... Flamer wrote in message oups.com... mistral wrote: Can no configure windows 98 for internet. PC was configured for small LAN, internet connection was via ISP router (broadband, via cable). Now i moved in another location and there is another ISP, via cableTV(broadband cable modem). ISP say, modem is already preconfigured. Broadband cable modem Thomson TCM425, connected to my PC. (it intended to share cable TV signal and internet). Internet signal come to modem, but it looks that PC just do not see modem. IE Browser status bar show 'Connecting to site: IP .. ..", but no any page loads. All worked normally in my previous ISP internet (LAN, broadband connection), I used this win98 box near five years in office and never had any problems. ISP engineer can no solve problem still. First visit engineer has connected modem and removed my previous connection settings, and just set few settings in 'Network' manually. This not help. (he dont used "Create a new connection" wizard). He tried ping - ping is OK. Next visit engineer replace two cable splitters, that split incoming singnal between twoTVs and PC with better ones. This not help also. Third visit engineer again replace splitter and suggested me replace my win 98 with winXP, then "all should work". I found that I can send and receive mail via my Outlook and Outlook Express previous mail configuration. (account was configured for LAN connection, via free pop3 server). But no any web pages loads. Where is problem and how to configure network settings? ISP have no ideas. thanks go to internet explorer, click tools, internet options, connections then unselect connect directly over lan and choose your cable connection in the box above, click apply, close ie, click start,run,type command ,enter then in thedos window type ipconfig /release_all then try open ie. Flamer. I checked this: there are no "cable connection" in Internet Explorer Options 'Connections' menu: there is 'Dial-up settings' -all boxes inactive, and 'LAN settings' button, which have(in LAN settings tab) "Automatically detect settings" checked, and 'Use a proxy server' box is unchecked. I have no LAN in my home. But there are *no* other selections in Internet Explorer 'Connections' tab. Also, I find no any directions or notes to this broadband cable modem in my PC(at least, i find no it). mistral uncheck the "Automatically detect settings" and give it a try I tried - not help. Just show message in status bar, with correct IP: 'Connecting to site: IP .. ..", or 'Opening page http://www.domain.com/ (if i type url in browser window) But no page loads. go to IE optionsconnections at the bottom there is a "LAN setup?" (don't have a win98 in front of me at the moment) step thru the LAN setup again and tell it how you connect (select "local gateway") |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Other or alternative Windows Updates | MEB | General | 3 | March 4th 06 04:20 AM |
Win98SE constant problems-ole32,shell32,other | MEB | General | 14 | January 15th 06 04:39 AM |
891711/MS05-002 Updated (fixed) for Win9x | David H. Lipman | General | 80 | April 21st 05 10:12 PM |
Registery problem? | Paul | General | 15 | December 8th 04 11:29 AM |
error loading explorer.exe. SHLWAPI.dll | Gary | General | 4 | October 20th 04 04:08 AM |