If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Windows Could Not Update
AFter updating, when I went to restart I received the
message Windows Could Not Update the file%1 from %2 %1: % 2. I found the way to solve this problem, but the problem I am having is that my computer won't reboot completely. The message remains on the screen and the startup process won't complete so I can fix the problem. Help! |
#2
|
|||
|
|||
Windows Could Not Update
Your "Windows Could Not Upgrade the File %1 from %2 %1: %2" error:
First boot to DOS using a floppy and check whether you have a WININIT.INI file in your C:\WINDOWS folder. If present rename it to something like wininit.old and try booting again. It is also probable that you will have to repeat the last software install or update that you made. See MS KB283069 - "Error Message: Windows Could Not Upgrade the File %1 from %2 %1: %2 (http://support.microsoft.com?kbid=283069). If you can't find a wininit.ini file then I suspect your problem is due to the C:\_RESTORE\TEMP folder having around 64K files in it which is the limit (2**16) for the number of files that can be located in a folder using the FAT32 filing system. This then results in the "Cannot upgrade file %1 from %2.." message when booting. I suggest you try deleting the _RESTORE folder with the loss of any system restore checkpoints you might have (not that I think they are now usable) and see if that solves the problem. Delete the folder as follows: a) Boot to DOS using a floppy. Do NOT choose "Minimal Boot" from the menu when booting from a floppy but rather choose "Start computer with (or without) CD-ROM support" otherwise the ATTRIB command will not be available. b) At the DOS A:\ prompt, type: ATTRIB -H -S -R C:\_RESTORE and then REN C:\_RESTORE OLDREST c) Remove the floppy d) Reboot your PC Another problem is that the update you were doing was never completed so your system may still be unusable and the update repeated. e) Delete the folder C:\OLDREST f) Check that an automatic system restore checkpoint was created. g) Finally adjust the space allocated to the restore folder: System | Performance | File System | Hard Disk and adjust the restore slider to your preferred setting. A figure of 200MB is normally more than adequate for day to day use allowing perhaps a week of checkpoints to be available although increasing this to perhaps 400MB for a few days during periods of large installs such Microsoft Office is advisable. --? Mike Maltby MS-MVP Fred Michael wrote: AFter updating, when I went to restart I received the message Windows Could Not Update the file%1 from %2 %1: % 2. I found the way to solve this problem, but the problem I am having is that my computer won't reboot completely. The message remains on the screen and the startup process won't complete so I can fix the problem. Help! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Microsoft Security Bulletin MS04-018 - Cumulative Security Update for Outlook Express (823353) | PA Bear | General | 5 | July 15th 04 05:49 AM |
Microsoft Security Bulletin MS04-024 - Vulnerability in Windows Shell Could Allow Remote Code Execution (839645) | Gary S. Terhune | General | 2 | July 14th 04 05:06 AM |
Microsoft Security Bulletin MS04-024 - Vulnerability in Windows Shell Could Allow Remote Code Execution (839645) | Gary S. Terhune | General | 2 | July 14th 04 05:06 AM |
Microsoft Security Bulletin MS04-023--Please Note! | Gary S. Terhune | General | 4 | July 14th 04 04:39 AM |
Windows update problem | Mack the knife | General | 0 | June 12th 04 08:21 PM |