If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
start-up message
When I'm starting up I get a message that says " Windows could not upgrade
the file %1 from %2" And on the line below it says " %1 : %2 " Also, after a freeze-up, when I do a "scan disc for errors" I'll only get to the %3 position and it will restart the scan. I lost my recovery disc so I can't do this. What can I do. |
#2
|
|||
|
|||
start-up message
The %1 %2 problem you saw is usually quite easy to fix and is often but
not exclusively the result of having Symantec's LiveUpdate installed. First boot to DOS using a floppy and check whether you have a WININIT.INI file in your C:\WINDOWS folder. If present rename it to something like wininit.old and try booting again. It is also probable that you will have to repeat the last software install or update that you made. See MS KB283069 - "Error Message: Windows Could Not Upgrade the File %1 from %2 %1: %2 (http://support.microsoft.com?kbid=283069). If you can't find a wininit.ini file then I suspect your problem is due to the C:\_RESTORE\TEMP folder having around 64K files in it which is the limit (2**16) for the number of files that can be located in a folder using the FAT32 filing system. This then results in the "Cannot upgrade file %1 from %2.." message when booting. I suggest you try deleting the _RESTORE folder with the loss of any system restore checkpoints you might have (not that I think they are now usable) and see if that solves the problem. Delete the folder as follows: a) Boot to DOS using a floppy. Do NOT choose "Minimal Boot" from the menu when booting from a floppy but rather choose "Start computer with (or without) CD-ROM support" otherwise the ATTRIB command will not be available. b) At the DOS A:\ prompt, type: ATTRIB -H -S -R C:\_RESTORE and then REN C:\_RESTORE OLDREST c) Remove the floppy d) Reboot your PC Another problem is that the install/update you were doing will not have been completely installed so your system may still be unusable and the install/update will need to be repeated. e) Delete the folder C:\OLDREST f) Check that an automatic system restore checkpoint was created. g) Finally adjust the space allocated to the restore folder: System | Performance | File System | Hard Disk and adjust the restore slider to your preferred setting. A figure of 200MB is normally more than adequate for day to day use allowing perhaps a week of checkpoints to be available although increasing this to perhaps 400MB for a few days during periods of large installs such Microsoft Office is advisable. -- Mike Maltby MS-MVP Windows bearpaw wrote: When I'm starting up I get a message that says " Windows could not upgrade the file %1 from %2" And on the line below it says " %1 : %2 " Also, after a freeze-up, when I do a "scan disc for errors" I'll only get to the %3 position and it will restart the scan. I lost my recovery disc so I can't do this. What can I do. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Problems with additional RAM aand NIC | Alan | Setup & Installation | 25 | September 2nd 06 09:36 PM |
Error Loading OS | Herman Berliss, MD | General | 29 | February 21st 05 03:44 PM |
during start up an error message....could not find file(or one | baaabaaaay | General | 14 | January 1st 05 11:27 PM |
Hibrinate error message on start up | Tom | General | 1 | August 26th 04 02:48 PM |
Start up Message | [email protected] | General | 2 | August 26th 04 05:24 AM |