A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows 98 » Monitors & Displays
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Unable to save changes in Win98SE display settings



 
 
Thread Tools Display Modes
  #1  
Old February 11th 05, 03:57 PM
Bonzy
external usenet poster
 
Posts: n/a
Default Unable to save changes in Win98SE display settings

One morning my Win98SE pc suffered apower surge when powered up; power supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only; this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However, when
I change colour setting to 16bit High colour and change pixels setting to 800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480 pixels.
Also it feezes often and I have to restart pc always. What have I done wrong
or what havent I done? Please help me out here. Thanx in advance.
  #2  
Old February 11th 05, 09:16 PM
Ron Badour
external usenet poster
 
Posts: n/a
Default

You have not loaded the proper video display adapter (video card)
driver--your W98 CD apparently doesn't have the driver. Here's my standard
blurb:

When the correct screen resolution (screen area) or the right number of
colors are not available choices in display properties, settings tab, then
it is a good bet you do not have the right driver installed for your display
adapter. The display adapter in your PC is either a video card or a display
chipset on the motherboard.

If you received a CD or floppy disks with drivers along with your PC, see if
they contain a display adapter driver and install it using: control panel,
system, device manager, display adapter.

If you know what display adapter your PC has but you have no disks, use
www.google.com to track down the correct driver on the internet.

If you do not know what display adapter your PC uses, you can go to a MS-DOS
prompt and type: Debug and hit enter. The screen will display a
flashing prompt next to a - sign. Type: DC000:35 (DC000:50 may also work)
and hit enter. The name and possibly model of your display adapter should
appear on the right hand side of the screen. To quit Debug, type Q and hit
enter. If Debug is not helpful, you can try this program: Advanced PCI
Info, available at: http://www.upsystems.com.ua/support/alexmina/ If all
else fails, you will have to remove the computer case. Look at where the
monitor plugs into the back of the case and then check that location inside
the case. If there is a card there, you obviously have a video card and if
not, you have on board graphics. Write down any information displayed on
either the card or the chipset on the motherboard. Then use www.google.com
to search for the information. Do not include all the data you found in one
search message--search on each piece individually. If you include all the
information at once, you might not get a hit.

I have found that a video card will generally have to be removed in order to
see the information. Be careful of static electricity as it can fry
components. Before touching anything in the computer case (the cord is
unplugged, right?), ground yourself to the case by touching it. Don't work
on carpeting since shuffling your feet on it can generate static electricity
after you grounded yourself. Remove the one screw that holds the card in
place and using a rocking motion (left to right and back), pull the card
straight out.

--
Regards

Ron Badour, MS MVP Windows 98
Tips: http://home.satx.rr.com/badour
Knowledge Base Info:
http://support.microsoft.com/default.aspx?pr=kbinfo

"Bonzy" wrote in message
...
One morning my Win98SE pc suffered apower surge when powered up; power
supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but
the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only;
this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device
manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However,
when
I change colour setting to 16bit High colour and change pixels setting to
800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480
pixels.
Also it feezes often and I have to restart pc always. What have I done
wrong
or what havent I done? Please help me out here. Thanx in advance.



  #3  
Old February 14th 05, 03:05 PM
Bonzy
external usenet poster
 
Posts: n/a
Default

Thanx, Ron. The display adapter is a video card that sits in the only AGP
slot on the m/board. This card is an s3 Trio3D/2X card. Unfortunately, I cant
locate the driver CDs or floppyies, and I've failed to download the driver
from driverguide.com. I'd identified it alright, but when I clicked on the
download button, the message I got on the screen was SURF CONTROL. ACCESS
DENIED. Harsh eh? What's up?
Besides, the pc is now in this nasty business of hanging/freezing; it hanges
or freezes so often that it is not possible to go any far in
troubleshooting-bad news! However, it never hangs/freezes in Safe Mode,
NEVER. What's the fix for this obstacle, Ron. What could be causing it? I
look forward to your response. Thanx in advance.

"Bonzy" wrote:

One morning my Win98SE pc suffered apower surge when powered up; power supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only; this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However, when
I change colour setting to 16bit High colour and change pixels setting to 800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480 pixels.
Also it feezes often and I have to restart pc always. What have I done wrong
or what havent I done? Please help me out here. Thanx in advance.

  #4  
Old February 14th 05, 05:09 PM
Ron Badour
external usenet poster
 
Posts: n/a
Default

http://www.surfcontrol.com/Default.a...=375&mnuid=1.1 Is this software
installed on the PC?

Something that is loading in normal mode, but not in safe mode, appears to
be causing the hang. I'd start in safe mode by doing a full screen with an
up to date anti virus program followed by a spyware hunt. Follow that with
clean boot troubleshooting to try to isolate what is causing the hang if it
still is doing it.

Spyware/scumware/adware are causing numerous system problems. I recommend
you download and use the following programs and consider removing everything
these programs identify. Be aware that there are frequent updates to these
programs and you need to check for them before every use.

AdAwa http://www.lavasoftusa.com/software/adaware/

CWShredder: http://www.spywareinfo.com/~merijn/cwschronicles.html (download
link near the bottom)

Spybot: http://www.safer-networking.org/

How to Perform Clean-Boot Troubleshooting for Windows 98
http://support.microsoft.com/?kbid=192926

--
Regards

Ron Badour, MS MVP Windows 98
Tips: http://home.satx.rr.com/badour
Knowledge Base Info:
http://support.microsoft.com/default.aspx?pr=kbinfo

"Bonzy" wrote in message
...
Thanx, Ron. The display adapter is a video card that sits in the only AGP
slot on the m/board. This card is an s3 Trio3D/2X card. Unfortunately, I
cant
locate the driver CDs or floppyies, and I've failed to download the driver
from driverguide.com. I'd identified it alright, but when I clicked on the
download button, the message I got on the screen was SURF CONTROL. ACCESS
DENIED. Harsh eh? What's up?
Besides, the pc is now in this nasty business of hanging/freezing; it
hanges
or freezes so often that it is not possible to go any far in
troubleshooting-bad news! However, it never hangs/freezes in Safe Mode,
NEVER. What's the fix for this obstacle, Ron. What could be causing it? I
look forward to your response. Thanx in advance.

"Bonzy" wrote:

One morning my Win98SE pc suffered apower surge when powered up; power
supply
gave out smoke and a burnig stench. PSU was changed, but windows failed
to
boot, it was re-installed without formatting drive C: . It went well but
the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only;
this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device
manager,
driver for the above graphics card is installed and no exclamation mark
is
seen. It is also stated that "This device is working properly". However,
when
I change colour setting to 16bit High colour and change pixels setting to
800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480
pixels.
Also it feezes often and I have to restart pc always. What have I done
wrong
or what havent I done? Please help me out here. Thanx in advance.



  #5  
Old February 15th 05, 10:59 AM
Bonzy
external usenet poster
 
Posts: n/a
Default

Thanx again Ron, I'm just about to start carrying out your great fixes. One
thing I need to mention to you though. Maybe it will help further.Sometime
last week I'd managed to get into device manager and was trying to update all
the drivers. Then somewhere in the middle, the screen went black and the ff:
error message came up:
Windows protection error. You need to restart your computer.
Press any key to continue..
After pressing 2 keys in succession the ff: error message came up:
An internal stack overflow has caused this session to be halted.
Change the STACKS setting in your CONFIG.SYS file and try again.
I didnt do that but pressed ctrl-alt-del just to restart, but there was no
response from the pc. I could only restart using the power button.
Does this information on its behavior help any further?
Thanx a million in advance.

"Bonzy" wrote:

One morning my Win98SE pc suffered apower surge when powered up; power supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only; this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However, when
I change colour setting to 16bit High colour and change pixels setting to 800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480 pixels.
Also it feezes often and I have to restart pc always. What have I done wrong
or what havent I done? Please help me out here. Thanx in advance.

  #6  
Old March 23rd 05, 04:24 AM
Thierry Plouchart
external usenet poster
 
Posts: n/a
Default

try this ftp://aiedownload.intel.com/df-suppo...g/win9xe67.exe
It should help.


"Bonzy" wrote in message
...
One morning my Win98SE pc suffered apower surge when powered up; power
supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but
the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only;
this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device
manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However,
when
I change colour setting to 16bit High colour and change pixels setting to
800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480
pixels.
Also it feezes often and I have to restart pc always. What have I done
wrong
or what havent I done? Please help me out here. Thanx in advance.



  #7  
Old March 24th 05, 11:37 AM
Bonzy
external usenet poster
 
Posts: n/a
Default

Thanks Thierry, but I've failed to get to this ftp site because when I tried,
the message on the monitor was: SURF CONTROL. ACCESS DENIED. Why do you think
the pc said this to me? Thanks.

"Thierry Plouchart" wrote:

try this ftp://aiedownload.intel.com/df-suppo...g/win9xe67.exe
It should help.


"Bonzy" wrote in message
...
One morning my Win98SE pc suffered apower surge when powered up; power
supply
gave out smoke and a burnig stench. PSU was changed, but windows failed to
boot, it was re-installed without formatting drive C: . It went well but
the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only;
this
is what monitor feeds on. Win98SE was reinstalled again. This time diplay
showed 16 colours, 256 colours and 16bit high colour only. In device
manager,
driver for the above graphics card is installed and no exclamation mark is
seen. It is also stated that "This device is working properly". However,
when
I change colour setting to 16bit High colour and change pixels setting to
800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480
pixels.
Also it feezes often and I have to restart pc always. What have I done
wrong
or what havent I done? Please help me out here. Thanx in advance.




  #8  
Old March 26th 05, 01:46 AM
PattyL
external usenet poster
 
Posts: n/a
Default

Configure "Surf Control" (apparently installed on your system) to allow you
to access exe files.

http://www.surfcontrol.com/

PattyL

"Bonzy" wrote in message
...
Thanks Thierry, but I've failed to get to this ftp site because when I
tried,
the message on the monitor was: SURF CONTROL. ACCESS DENIED. Why do you
think
the pc said this to me? Thanks.

"Thierry Plouchart" wrote:

try this ftp://aiedownload.intel.com/df-suppo...g/win9xe67.exe
It should help.


"Bonzy" wrote in message
...
One morning my Win98SE pc suffered apower surge when powered up; power
supply
gave out smoke and a burnig stench. PSU was changed, but windows failed
to
boot, it was re-installed without formatting drive C: . It went well
but
the
display was 16 colour only. Pc has an s3 Trio 3D/2X graphics card only;
this
is what monitor feeds on. Win98SE was reinstalled again. This time
diplay
showed 16 colours, 256 colours and 16bit high colour only. In device
manager,
driver for the above graphics card is installed and no exclamation mark
is
seen. It is also stated that "This device is working properly".
However,
when
I change colour setting to 16bit High colour and change pixels setting
to
800
by 600 pixels and restart, it remanins on 16 colours and 640 by 480
pixels.
Also it feezes often and I have to restart pc always. What have I done
wrong
or what havent I done? Please help me out here. Thanx in advance.






 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Tough one: Display settings won't save in Windows 98 [email protected] General 3 January 17th 05 09:12 AM
Can't change display settings Ian A Monitors & Displays 7 July 11th 04 08:19 PM
Problem with display settings h.eckstein Monitors & Displays 1 June 22nd 04 12:56 AM
problem with display settings dave Monitors & Displays 1 June 10th 04 02:31 AM
unable to upgrade to Win98SE from Win95 Rex Ripplinger Setup & Installation 1 June 3rd 04 05:38 PM


All times are GMT +1. The time now is 08:31 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 Win98banter.
The comments are property of their posters.