If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Scan Disk Problem
When I try to use Scandisk it says that there is another application
controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary |
#2
|
|||
|
|||
I sent this to System Tools group as I thought it should have there in the
first place. Sorry for the duplication but will be happy with an answer no matter where it comes from. Gary "Gary Goodings" wrote in message ... When I try to use Scandisk it says that there is another application controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary |
#3
|
|||
|
|||
Try ScanDefrag in Restrictive Mode, see the Readme for
a how-to. http://home.earthlink.net/~bblanton2...efrag/main.htm or http://www.blueorbsoft.com/scandefrag/index.html Gary Goodings wrote: When I try to use Scandisk it says that there is another application controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary |
#4
|
|||
|
|||
"Gary Goodings" wrote in message
... When I try to use Scandisk it says that there is another application controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary Have you tried holding down F2 during bootup to get into Safe Mode? Regards Mike. |
#5
|
|||
|
|||
I took the advice from another group to use my floppy start-up disk (saved
way back) and run the Scandisk in DOS mode. After about 3 hours of running, there were 4 files that had problems and they were fixed. Now all is OK and the PC is back to where it should be. Thanks for all the help. Gary "Mike Cawood, HND BIT" wrote in message ... "Gary Goodings" wrote in message ... When I try to use Scandisk it says that there is another application controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary Have you tried holding down F2 during bootup to get into Safe Mode? Regards Mike. |
#6
|
|||
|
|||
Go to diskeeper.com and download their trial copy of disk defragmenter. You
can run it no matter what else is running. "Gary Goodings" wrote: When I try to use Scandisk it says that there is another application controlling the Hard Drive and to wait till it stops and try again. I have waited for three days and it still has the message. Also I cannot get the PC to boot in Safe Mode. F8, delete, escape and using the control key won't start the Safe Mode. I can get the PC to go into Setup with the F1 key but nothing seems to be wrong there. I used the Default settings before Exiting the Setup. Gary |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Scan Disk Hangs | Quentin | Improving Performance | 6 | January 4th 05 10:56 PM |
Scan disk at start up..every time | TKinHawaii | General | 1 | November 13th 04 07:28 PM |
Please help! Display settings !! | Mitzi | Monitors & Displays | 12 | July 11th 04 05:19 AM |
MBR switch on FDISK | jt3 | General | 30 | June 21st 04 08:56 PM |
Scan Disk Defrag stop - Disk Surface Corrupted? | Laura Lee | Disk Drives | 1 | May 20th 04 08:56 AM |