If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Problem device in Device Manager in 98SE
Here is the problem device everyone -- any ideas
PCI Universal Serial Bus Unknown This Device Has a Problem: Code=28 (0x1C) The drivers for this device are not installed correctly. To install the driver for this device, click the Driver tab, and then click Update Driver. Registry Key: HKEY_LOCAL_MACHINE\enum\PCI\VEN_1039&DEV_7002&SUBS YS_810E1043&REV_00\BUS_00&D EV_03&FUNC_03 Alloc resources: Logical Configuration 0 Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF Forced resources: None Boot resources: Logical Configuration 0 Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF Filtered resources: None Basic resources: Logical Configuration 0 IRQ: 0 Mask: xFFFF Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF HW Revision: 000 Driver: Driver Not Installed |
#2
|
|||
|
|||
When in the BIOS, did you by any chance enable USB 2.0? If so, disable =
it and see if the "unknown" device goes away. If it does, you either = need 2.0 drivers or your device isn't capable of using 2.0. --=20 Brian A. Conflicts start where information lacks. http://www.dts-l.org/goodpost.htm "Dan" wrote in message = ... Here is the problem device everyone -- any ideas =20 =20 PCI Universal Serial Bus Unknown This Device Has a Problem: Code=3D28 (0x1C) The drivers for this device are not installed correctly. To install = the driver for this device, click the Driver tab, and then click Update Driver. Registry Key: = HKEY_LOCAL_MACHINE\enum\PCI\VEN_1039&DEV_7002&SUBS YS_810E1043&REV_00\BUS_= 00&D EV_03&FUNC_03 Alloc resources: Logical Configuration 0 Memory Address Range: Base=3D xFF6FF000 End=3D xFF6FFFFF = Min=3D x00000000 Max=3D xFFFFFFFF Forced resources: None Boot resources: Logical Configuration 0 Memory Address Range: Base=3D xFF6FF000 End=3D xFF6FFFFF = Min=3D x00000000 Max=3D xFFFFFFFF Filtered resources: None Basic resources: Logical Configuration 0 IRQ: 0 Mask: xFFFF Memory Address Range: Base=3D xFF6FF000 End=3D xFF6FFFFF = Min=3D x00000000 Max=3D xFFFFFFFF HW Revision: 000 Driver: Driver Not Installed =20 |
#3
|
|||
|
|||
This appears to be a SIS USB 2 controller. Remove the drivers and reinstall
them. The drivers are probably part of the motherboard driver set. Removing from safe mode is the best option, as you can check whether there are other inactive devices that should be removed. The chipset should allow a choice of USB 1.1 or USB 2 - if the correct drivers for 2 aren't available you could select 1.1. The chipset should support multiple controllers (3, from memory). In this case it can happen that trying to disable one of the controllers in BIOS setup is not effective, and can result in a failed driver installation, so make sure all USB controllers are enabled. -- Jeff Richards MS MVP (Windows - Shell/User) "Dan" wrote in message ... Here is the problem device everyone -- any ideas PCI Universal Serial Bus Unknown This Device Has a Problem: Code=28 (0x1C) The drivers for this device are not installed correctly. To install the driver for this device, click the Driver tab, and then click Update Driver. Registry Key: HKEY_LOCAL_MACHINE\enum\PCI\VEN_1039&DEV_7002&SUBS YS_810E1043&REV_00\BUS_00&D EV_03&FUNC_03 Alloc resources: Logical Configuration 0 Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF Forced resources: None Boot resources: Logical Configuration 0 Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF Filtered resources: None Basic resources: Logical Configuration 0 IRQ: 0 Mask: xFFFF Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= x00000000 Max= xFFFFFFFF HW Revision: 000 Driver: Driver Not Installed |
#4
|
|||
|
|||
Well the problem is solved and all devices are working. I decided to use the
process of elimination and I updated the problem driver with my Motherboard CD and I eventually found the device. I went through everything in the cd and checked each time there was an okay. Finally, I found something that would work but I continued through the rest of the cd just to make sure there was not another option. The controller is Standard Enhanced PCI to USB Host Controller. I appreciate the help Brian but your answer did not happen to be the solution. PCR, thanks for making an attempt in a previous post. Jeff Richards, thank you so much for setting me on the right track. I reviewed the BIOS and realized the answer was not there and then I decided that I needed to go through the long process of checking the Motherboard cd. Your answer pointed me in the right direction and told me that it was the motherboard cd that I needed to be focused upon when you said "This appears to be a SIS USB 2 controller." Thank you again for setting me on the right track and your MVP status is well-deserved, imho. Have a great Saturday! :~ "Jeff Richards" wrote in message ... : This appears to be a SIS USB 2 controller. Remove the drivers and reinstall : them. The drivers are probably part of the motherboard driver set. Removing : from safe mode is the best option, as you can check whether there are other : inactive devices that should be removed. The chipset should allow a choice : of USB 1.1 or USB 2 - if the correct drivers for 2 aren't available you : could select 1.1. The chipset should support multiple controllers (3, from : memory). In this case it can happen that trying to disable one of the : controllers in BIOS setup is not effective, and can result in a failed : driver installation, so make sure all USB controllers are enabled. : -- : Jeff Richards : MS MVP (Windows - Shell/User) : "Dan" wrote in message : ... : Here is the problem device everyone -- any ideas : : : PCI Universal Serial Bus : Unknown : This Device Has a Problem: Code=28 (0x1C) : The drivers for this device are not installed correctly. To install the : driver : for this device, click the Driver tab, and then click Update Driver. : Registry Key: : HKEY_LOCAL_MACHINE\enum\PCI\VEN_1039&DEV_7002&SUBS YS_810E1043&REV_00\BUS_00&D : EV_03&FUNC_03 : Alloc resources: Logical Configuration 0 : Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= : x00000000 Max= xFFFFFFFF : Forced resources: None : Boot resources: Logical Configuration 0 : Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= : x00000000 Max= xFFFFFFFF : Filtered resources: None : Basic resources: Logical Configuration 0 : IRQ: 0 Mask: xFFFF : Memory Address Range: Base= xFF6FF000 End= xFF6FFFFF Min= : x00000000 Max= xFFFFFFFF : HW Revision: 000 : Driver: Driver Not Installed : : : : |
#5
|
|||
|
|||
Now that may be a good thing or not.=20
How long have you had the machine? Have you updated the BIOS since possession? If you're not running into many problems, leave well enough alone. Otherwise, you mention here/there about running 98/XP. Is this a dual = boot environment? If so, some of you're issues may be due to an older = BIOS that may need to be updated. Check the mobo manufacturers site for = an updated BIOS and updated drivers. Others may correct me if I'm off base, but the same settings you use in = the bios are used by both OS's. AFAIK they are not BIOS independent in a = dual boot and the settings for one OS may not be to the liking of the = other. **WARNING** If you have never performed a BIOS update, READ THE INSTRUCTIONS = provided by the manufacturer on noting all BIOS settings, backing up, = updating and restoring. If you are not comfortable or have even the = slightest doubt, DO NOT attempt it or you "may" truly be updating the = BIOS with a new CPU.=20 --=20 Brian A. Conflicts start where information lacks. http://www.dts-l.org/goodpost.htm |
#6
|
|||
|
|||
Brian A., I have flashed BIOS's before and I do not plan on flashing my BIOS
unless the new BIOS gives me some new feature that I want. It is like you have warned, Brian that too many things could go wrong especially fried component(s) and anyway this PC was updated and the BIOS is only a year old. I formatted and reinstalled my computer both the 98SE side and the XP side on the new year and that is the only reason I was having some trouble. The last time a professional helped me and this time I did the format and complete reinstall by myself with help from this newsgroup of course. I am confident that everything is now okay but thanks again for the warning and I know you mean well by leaving everything alone but in this case this needed fixing because of the reinstallation and XP for its benefit is much better at automatically configuring drivers as opposed to 98SE where you have to get down and dirty so to say to configure it just right and this as well as being aware of what everything in my system is doing is extremely important to me and if I suffer consequences then I will deal with them at that time. I am extremely *fussy* in this regard and perhaps someday have the makings of a computer tech. LOL "Brian A." gonefish'n@afarawaylake wrote in message ... Now that may be a good thing or not. How long have you had the machine? Have you updated the BIOS since possession? If you're not running into many problems, leave well enough alone. Otherwise, you mention here/there about running 98/XP. Is this a dual boot environment? If so, some of you're issues may be due to an older BIOS that may need to be updated. Check the mobo manufacturers site for an updated BIOS and updated drivers. Others may correct me if I'm off base, but the same settings you use in the bios are used by both OS's. AFAIK they are not BIOS independent in a dual boot and the settings for one OS may not be to the liking of the other. **WARNING** If you have never performed a BIOS update, READ THE INSTRUCTIONS provided by the manufacturer on noting all BIOS settings, backing up, updating and restoring. If you are not comfortable or have even the slightest doubt, DO NOT attempt it or you "may" truly be updating the BIOS with a new CPU. -- Brian A. Conflicts start where information lacks. http://www.dts-l.org/goodpost.htm |
#7
|
|||
|
|||
You're welcome, and thanks for letting us known that you sorted it out.
-- Jeff Richards MS MVP (Windows - Shell/User) "Dan" wrote in message ... Well the problem is solved and all devices are working. I decided to use the process of elimination and I updated the problem driver with my Motherboard CD and I eventually found the device. I went through everything in the cd and checked each time there was an okay. Finally, I found something that would work but I continued through the rest of the cd just to make sure there was not another option. The controller is Standard Enhanced PCI to USB Host Controller. I appreciate the help Brian but your answer did not happen to be the solution. PCR, thanks for making an attempt in a previous post. Jeff Richards, thank you so much for setting me on the right track. I reviewed the BIOS and realized the answer was not there and then I decided that I needed to go through the long process of checking the Motherboard cd. Your answer pointed me in the right direction and told me that it was the motherboard cd that I needed to be focused upon when you said "This appears to be a SIS USB 2 controller." Thank you again for setting me on the right track and your MVP status is well-deserved, imho. Have a great Saturday! |
#8
|
|||
|
|||
"Dan" wrote in message =
... Brian A., I have flashed BIOS's before and I do not plan on flashing = my BIOS unless the new BIOS gives me some new feature that I want. It is like = you have warned, Brian that too many things could go wrong especially = fried component(s) and anyway this PC was updated and the BIOS is only a = year old. It's standard for me to inform/warn anyone one I respond to in regards = to any major system changes. I know not the level of knowledge each = individual has and failing/omitting any warning IMO would be negligent = and/or possibly disasterous. I formatted and reinstalled my computer both the 98SE side and the XP = side on the new year and that is the only reason I was having some trouble. = The last time a professional helped me and this time I did the format and = complete reinstall by myself with help from this newsgroup of course. I am = confident that everything is now okay but thanks again for the warning and I = know you mean well by leaving everything alone but in this case this needed = fixing "leave well enough alone" was only in refernce to updating the BIOS. = Although, it can be said to some who don't have a problem, read some = posts and decide that something they read should be done without fully = being aware of it's implementation purpose, or what if any, = reprocussions may be. because of the reinstallation and XP for its benefit is much better at automatically configuring drivers as opposed to 98SE where you have to = get down and dirty so to say to configure it just right and this as well = as being aware of what everything in my system is doing is extremely important = to me and if I suffer consequences then I will deal with them at that time. = I am extremely *fussy* in this regard and perhaps someday have the makings = of a computer tech. LOL Actually, IMO I think 98 is easier to configure for the seasoned users, = mainly on the look/feel/performance level. XP, especially Pro has many = hidden secret settings that may be altered/tweaked. Some are easy enough = for the greenhorn with guidance while others should only be done by = daredevils, or those with the total knowledge of the effect the change = will have, and this isn't including the registry or Recovery Console. Anyhoo, glad to hear all is working now, I'm 86'n. --=20 Brian A. Conflicts start where information lacks. http://www.dts-l.org/goodpost.htm |
#9
|
|||
|
|||
|
#10
|
|||
|
|||
Thanks Brian and I misunderstood your post. My profuse apologies and I am
glad everything is now okay with my system. I thought you were referring to not fixing the ? device driver. "Brian A." gonefish'n@afarawaylake wrote in message ... "Dan" wrote in message ... Brian A., I have flashed BIOS's before and I do not plan on flashing my BIOS unless the new BIOS gives me some new feature that I want. It is like you have warned, Brian that too many things could go wrong especially fried component(s) and anyway this PC was updated and the BIOS is only a year old. It's standard for me to inform/warn anyone one I respond to in regards to any major system changes. I know not the level of knowledge each individual has and failing/omitting any warning IMO would be negligent and/or possibly disasterous. I formatted and reinstalled my computer both the 98SE side and the XP side on the new year and that is the only reason I was having some trouble. The last time a professional helped me and this time I did the format and complete reinstall by myself with help from this newsgroup of course. I am confident that everything is now okay but thanks again for the warning and I know you mean well by leaving everything alone but in this case this needed fixing "leave well enough alone" was only in refernce to updating the BIOS. Although, it can be said to some who don't have a problem, read some posts and decide that something they read should be done without fully being aware of it's implementation purpose, or what if any, reprocussions may be. because of the reinstallation and XP for its benefit is much better at automatically configuring drivers as opposed to 98SE where you have to get down and dirty so to say to configure it just right and this as well as being aware of what everything in my system is doing is extremely important to me and if I suffer consequences then I will deal with them at that time. I am extremely *fussy* in this regard and perhaps someday have the makings of a computer tech. LOL Actually, IMO I think 98 is easier to configure for the seasoned users, mainly on the look/feel/performance level. XP, especially Pro has many hidden secret settings that may be altered/tweaked. Some are easy enough for the greenhorn with guidance while others should only be done by daredevils, or those with the total knowledge of the effect the change will have, and this isn't including the registry or Recovery Console. Anyhoo, glad to hear all is working now, I'm 86'n. -- Brian A. Conflicts start where information lacks. http://www.dts-l.org/goodpost.htm |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Printer & Device Manager | Roger Fink | General | 7 | October 15th 04 12:42 PM |
98SE stalling problem. | TerryS | General | 2 | October 12th 04 09:35 PM |
optical mouse problem in 98SE | Jeff | General | 4 | June 23rd 04 03:45 PM |
Question on Device Manager settings | Jane B | General | 6 | June 15th 04 11:06 PM |
Zero-byte D: drive should not show, C: missing from Device Manager | *Vanguard* | General | 8 | June 12th 04 04:19 AM |