If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Missing TCP/IP Protocol-Install USB to Ethernet Adapter
Hello,
I am trying to install/use a Siemens Speedstream USB 10/100 Ethernet Adapter on a Gateway SOLO 9300 CX running Windows 98SE. During the install a file was declared missing from C: drive (sorry went so fast I missed the file name), yet driver from CD was installed ok and shows up in list of network adapters under Device Manager. Called local cable company to debug my problem and they conclude after running winipcfg that the TCP/IP protocol for the adapter is missing. The adapter does not show in the pull down. When I go to windows control panel/network to ADD protocol, nothing happens. I am stuck and not sure where to turn. I tried Gateway support with no progress and have not been able to contact Siemens which is my next step. Peace, GR |
#2
|
|||
|
|||
Missing TCP/IP Protocol-Install USB to Ethernet Adapter
Have you tried restarting the computer from cold and then trying to add the
TCP/IP protocol? "gramsay" wrote in message ... Hello, I am trying to install/use a Siemens Speedstream USB 10/100 Ethernet Adapter on a Gateway SOLO 9300 CX running Windows 98SE. During the install a file was declared missing from C: drive (sorry went so fast I missed the file name), yet driver from CD was installed ok and shows up in list of network adapters under Device Manager. Called local cable company to debug my problem and they conclude after running winipcfg that the TCP/IP protocol for the adapter is missing. The adapter does not show in the pull down. When I go to windows control panel/network to ADD protocol, nothing happens. I am stuck and not sure where to turn. I tried Gateway support with no progress and have not been able to contact Siemens which is my next step. Peace, GR |
#3
|
|||
|
|||
Missing TCP/IP Protocol-Install USB to Ethernet Adapter
Have you tried restarting the computer from cold and then trying to add the
TCP/IP protocol? "gramsay" wrote in message ... Hello, I am trying to install/use a Siemens Speedstream USB 10/100 Ethernet Adapter on a Gateway SOLO 9300 CX running Windows 98SE. During the install a file was declared missing from C: drive (sorry went so fast I missed the file name), yet driver from CD was installed ok and shows up in list of network adapters under Device Manager. Called local cable company to debug my problem and they conclude after running winipcfg that the TCP/IP protocol for the adapter is missing. The adapter does not show in the pull down. When I go to windows control panel/network to ADD protocol, nothing happens. I am stuck and not sure where to turn. I tried Gateway support with no progress and have not been able to contact Siemens which is my next step. Peace, GR |
#4
|
|||
|
|||
Missing TCP/IP Protocol-Install USB to Ethernet Adapter
Yes .... still wont work.
"Alan" wrote: Have you tried restarting the computer from cold and then trying to add the TCP/IP protocol? "gramsay" wrote in message ... Hello, I am trying to install/use a Siemens Speedstream USB 10/100 Ethernet Adapter on a Gateway SOLO 9300 CX running Windows 98SE. During the install a file was declared missing from C: drive (sorry went so fast I missed the file name), yet driver from CD was installed ok and shows up in list of network adapters under Device Manager. Called local cable company to debug my problem and they conclude after running winipcfg that the TCP/IP protocol for the adapter is missing. The adapter does not show in the pull down. When I go to windows control panel/network to ADD protocol, nothing happens. I am stuck and not sure where to turn. I tried Gateway support with no progress and have not been able to contact Siemens which is my next step. Peace, GR |
#5
|
|||
|
|||
Missing TCP/IP Protocol-Install USB to Ethernet Adapter
Yes .... still wont work.
"Alan" wrote: Have you tried restarting the computer from cold and then trying to add the TCP/IP protocol? "gramsay" wrote in message ... Hello, I am trying to install/use a Siemens Speedstream USB 10/100 Ethernet Adapter on a Gateway SOLO 9300 CX running Windows 98SE. During the install a file was declared missing from C: drive (sorry went so fast I missed the file name), yet driver from CD was installed ok and shows up in list of network adapters under Device Manager. Called local cable company to debug my problem and they conclude after running winipcfg that the TCP/IP protocol for the adapter is missing. The adapter does not show in the pull down. When I go to windows control panel/network to ADD protocol, nothing happens. I am stuck and not sure where to turn. I tried Gateway support with no progress and have not been able to contact Siemens which is my next step. Peace, GR |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
No protocol for wireless adapter (also using dial-up) | Richard G. Harper | General | 9 | May 24th 05 07:34 AM |
My Network Places hangs | MBD | Networking | 12 | September 4th 04 01:58 AM |
PCI Ethernet | Star | General | 14 | July 18th 04 03:59 PM |
Illegal operation | Susan | General | 14 | July 1st 04 11:54 PM |
missing or corrupt file prevents install | Pablo | General | 7 | June 23rd 04 03:40 PM |