If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
ME reinstallation
ok, to make a long story short, I starting having trouble with my computer.
It is an old Gateway, I have ME installed on it now. I booted up the other night and a blue screen came up with this message "Windows protection error. You need to restart your computer. System halted." So I restarted in safe mode, then started troubleshooting in the system config utility. Ended up finding that when I startup without the file ndis.VXD the computer will start fine. Only problem now is that I have no Internet. So off to Microsoft Knowledge Base and ran across this article 261766 - Hang at Startup or Shutdown with Ndis.vxd Enabled Followed the instructions in this article and found out that I have a hardware conflict. 133240 Troubleshooting Device Conflicts with Device Manager My device that has the conflict seems to be my network adapter. I have a Seimens Speedstream PCI 10/100 installed. Under the properties tabgeneral then under device status this is the message. This device is not working properly because Windows cannot load the file( ndis.VXD , ntkem.VXD , ndis.vxd) that loads the drivers for the device [code 8] To fix this problem, run windows setup again using your windows CD-ROM. Now my Windows cd is on a Gateway System Restoration Kit, if I run windows setup from my restoration cd, will I lose everything on my computer now, or will it basically just write what files I need or what? Or is there another way that I can get these files restored without having to go through the setup? Sorry for the long explanation for such a short question, but I just wanted to provide the history of what I had already tried. Thanks, Brian |
#2
|
|||
|
|||
ME reinstallation
Do an over-the-top install from the HD - look here for detailed
instructions. http://www.btinternet.com/~winnoel/reinME.htm post back with any questions (or use the feedback link on the site) -- Noel Paton (MS-MVP 2002-2004, Win9x) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm Please read http://dts-l.org/goodpost.htm on how to post messages to NG's or http://www.microsoft.com/presspass/f.../Mar27pmvp.asp "Brian" wrote in message ... ok, to make a long story short, I starting having trouble with my computer. It is an old Gateway, I have ME installed on it now. I booted up the other night and a blue screen came up with this message "Windows protection error. You need to restart your computer. System halted." So I restarted in safe mode, then started troubleshooting in the system config utility. Ended up finding that when I startup without the file ndis.VXD the computer will start fine. Only problem now is that I have no Internet. So off to Microsoft Knowledge Base and ran across this article 261766 - Hang at Startup or Shutdown with Ndis.vxd Enabled Followed the instructions in this article and found out that I have a hardware conflict. 133240 Troubleshooting Device Conflicts with Device Manager My device that has the conflict seems to be my network adapter. I have a Seimens Speedstream PCI 10/100 installed. Under the properties tabgeneral then under device status this is the message. This device is not working properly because Windows cannot load the file( ndis.VXD , ntkem.VXD , ndis.vxd) that loads the drivers for the device [code 8] To fix this problem, run windows setup again using your windows CD-ROM. Now my Windows cd is on a Gateway System Restoration Kit, if I run windows setup from my restoration cd, will I lose everything on my computer now, or will it basically just write what files I need or what? Or is there another way that I can get these files restored without having to go through the setup? Sorry for the long explanation for such a short question, but I just wanted to provide the history of what I had already tried. Thanks, Brian |
#3
|
|||
|
|||
ME reinstallation
On Tue, 22 Jun 2004 18:18:16 -0700, "Brian"
"Windows protection error. You need to restart your computer. System halted." That is usually one of: - flaky hardware - device driver issues So step 1 is to back away and verify hardware integrity before allowing Windows to run again, as per http://cquirke.mvps.org/9x/bthink.htm Once you know that your hardware's OK (i.e. no HD or RAM errors, not overclocked, fans OK etc.) and there's no active malware, you can get back into Windows and zoom into specifics. So I restarted in safe mode, then started troubleshooting in the system config utility. Ended up finding that when I startup without the file ndis.VXD the computer will start fine. Only problem now is that I have no Internet. So off to Microsoft Knowledge Base and ran across this article 261766 - Hang at Startup or Shutdown with Ndis.vxd Enabled Followed the instructions in this article and found out that I have a hardware conflict. 133240 Troubleshooting Device Conflicts with Device Manager My device that has the conflict seems to be my network adapter. I have a Seimens Speedstream PCI 10/100 installed. Under the properties tabgeneral then under device status this is the message. Test that by setting the device to "disable in this profile" and see if that works, even with the .VXD in effect. You may also want to check C:\Scandisk.log to see whether any code files such as that .vxd were "fixed" (or "cleaned" by av, in av logs). This device is not working properly because Windows cannot load the file( ndis.VXD , ntkem.VXD , ndis.vxd) that loads the drivers for the device [code 8] To fix this problem, run windows setup again using your windows CD-ROM. Don't do that. What I'd do first is: - copy the relevant .VXD to another location - extract the relevant .VXD from WinME CD - rt-click and compare Version tab in Properties - compare the code contents via FC /B If the versions are supposed to be the same but FC shows the content differs, then likely the old ones were corrupted. Now my Windows cd is on a Gateway System Restoration Kit, if I run windows setup from my restoration cd, will I lose everything on my computer now, or will it basically just write what files I need or what? It will likely nuke the whole thing. Don't do that. I can get these files restored without having to go through the setup? Extract /A is your friend. Use Extract /? to find how to use it :-) -------------------- ----- ---- --- -- - - - - Reality is that which, when you stop believing in it, does not go away (PKD) -------------------- ----- ---- --- -- - - - - |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ME Reinstallation (Clean Install) Problems | RN | Setup & Installation | 56 | July 8th 04 02:03 PM |
ME reinstallation produced "SUWIN caused GPF in module verx.dll" - amongst other things | bitemebutt | Setup & Installation | 4 | June 22nd 04 12:15 PM |