If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
TVdebug.log from Zonealarm?
Hi forum,
During my weekly maintenance of the disc-controller i found every time a fault on the file TVdebug.log file? What can be the reason? Regards Huib |
#2
|
|||
|
|||
You don't mention the type of fault? Is it date error or what? What
version of ZA are you using? I'm running ZA Pro v5.1.033.000 and am seeing nothing similar here. -- Mike Maltby MS-MVP [2001-2005] Huib wrote: Hi forum, During my weekly maintenance of the disc-controller i found every time a fault on the file TVdebug.log file? What can be the reason? |
#3
|
|||
|
|||
I assume you had error messages while using scandisk. Probably the file
is damaged due to a bad shutdown. Scandisk will not be able to repair the error if ZA is working. The easiest thing to do is shut down ZA temporarily, delete tvdebug.log and restart. Good luck MP "Huib" wrote in message ... Hi forum, During my weekly maintenance of the disc-controller i found every time a fault on the file TVdebug.log file? What can be the reason? Regards Huib |
#4
|
|||
|
|||
Haalo Mike,
I am using the same version. I donīt have a real problem it is only during scandisk that the file every time is faulty. See also my reply in the MP. regards Huib "Mike M" schreef in bericht ... You don't mention the type of fault? Is it date error or what? What version of ZA are you using? I'm running ZA Pro v5.1.033.000 and am seeing nothing similar here. -- Mike Maltby MS-MVP [2001-2005] Huib wrote: Hi forum, During my weekly maintenance of the disc-controller i found every time a fault on the file TVdebug.log file? What can be the reason? |
#5
|
|||
|
|||
Hallo PM & Mike,
When i am performing scandisk ZA is disabled. Everytime i do delete the file during scandisk and further i have no problems. But, a few days later when i perform again a scandisk i have the same symptom. So, there is clearly something wrong with that file. Can the use be avoided ? I am not interested in the logging of possible problems? Regards Huib "masterprometheus" schreef in bericht ... I assume you had error messages while using scandisk. Probably the file is damaged due to a bad shutdown. Scandisk will not be able to repair the error if ZA is working. The easiest thing to do is shut down ZA temporarily, delete tvdebug.log and restart. Good luck MP "Huib" wrote in message ... Hi forum, During my weekly maintenance of the disc-controller i found every time a fault on the file TVdebug.log file? What can be the reason? Regards Huib |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
ZoneAlarm Pro uopdate: | looneytunes>verizone.net | General | 9 | October 3rd 04 12:29 AM |
Latest verdict on ZoneAlarm Pro V5.0.590.043 ?? | Steve | General | 5 | July 27th 04 08:41 PM |
EZ Armour (ZoneAlarm Lite) Firewall hanging? | jt3 | General | 8 | July 17th 04 09:09 AM |
ZoneAlarm missing Firewall Zones tab for subnet. New NAT router won't show Entire Network. | Networking | 5 | July 5th 04 09:48 AM | |
ZoneAlarm missing Firewall Zones tab for subnet. New NAT router won't show Entire Network. | Networking | 5 | July 5th 04 09:48 AM |