If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
invalid hibernation partition/file????
Aas a followup.
I pulled the battery and the startup stops on the first page asking for; Press F1 to run SETUP Press F2 to load default values and continue Anyway the info is as follows. American Megatrends Release 11/21/2001 AMIBIOS (C)2000 American Megatrends Inc. BIOS ver 2.09 NS570 KBC Version: 1.17 Pentium III,1GHz Checking NVRAM... 253952KB OK ICS9248-146 Inside WAIT.... CMOS Battery Low Press F1------- Press F2------- (C) American Megatrends Inc. 62-0213-009999-001010000-071595-SIS630-1AA0G008-W If I press F1 goes into BIOS. F2 load defualts and goes to page 2 of setup. Page 2: Main Processor :Pentium III Math Processor :Built-IN Base Mem Size : 640KB Floppy Drive A: :1.44 MB 31/2" Ext. mem Size : 247MB Floppy b none Seriall 3F8 Display Type VGA/EGA Parallel Port 378 AMIBIOS date 11/21/2001 Proc. Clock 1GHZ Exter. Cache 256KB, Enabled Power Mage. Enabled Hard Disk Cyl Head Sector Size LBA 32Bit Block PIO UDMA Mode Mode Mode Mode Mode Primary Master : 58140 16 63 30006MB LBA On 16Sec 4 4 Sec. Master : DVD-ROM 4 2 PCI Devices: Onboard IDE Onboard Comm. Device, IRQ10 Onboard Multimedia Dev. IRQ11 " USB Contr., IRQ9 " USB Control. IRQ9 " Ethernet, IRQ10 " PCI Bridge " CardBus Bridge Bridge VGA SDRAM at DIMM # :1 Invalid HIBERNATION partition/file...RUN HDPREPEZ... Do you want to (B)oot or (P)ower down? __ *** Not sure if any of this helps or not********** "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#12
|
|||
|
|||
invalid hibernation partition/file????
Well here's where we a Everything I can find on this message, which is
common to many laptops that use the same Hibernation system... All roads lead to those same instructions you already tried. The file that the message suggests you run, if you could read the whole message, is "HDPREP (or HDPREPEZ), or 'AMI Save to File Utility'". That would prepare the hard drive by creating a special partition to hold Hibernation data. But you have to prep the HD *before* you turn on the feature, and you have to turn off the feature to make it let you boot if the HD isn't prepped properly. In short, I'm not sure I can take you any farther. If there is no possible power management option that fits the bill, I have to wonder if someone tried to update the BIOS and screwed up. I dunno, nothing quite makes sense. All I know is that it's the BIOS that's holding you up, and it's holding you up because it can't find the hibernation partition. Hmmm... I suppose you could try taking out the HD, putting it into a desktop, and run the HDPREP program, then put it back in the laptop. Would be a complicated operation (gotta make sure only the laptop HD gets "prepped", which might mean having to disable the rest of the HDs in the machine and use a bootable floppy setup disk to run the HDPREP utility. But it all comes back to BIOS should have that setting, and if it doesn't, nothing makes sense. Sorry, but I don't think I could come up with anything else without the machine in front of me. I'd want to take the disk out and put it into another machine to see what partitions there are, and I'd want to positively identify the motherboard and determine if it was possible to find a BIOS version for it that has the proper settings... Just doesn't make any sense. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#13
|
|||
|
|||
invalid hibernation partition/file????
I assume that when you choose Boot when asked at the end, nothing happens?
CMOS battery low would explain the error message IF that Save to File or whatever setting existed. There's only one Power Management setting? It looks like it's enabled. It doesn't have any kind of sub-menu with a bunch of other PM-related settings? Did you try disabling PM? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Aas a followup. I pulled the battery and the startup stops on the first page asking for; Press F1 to run SETUP Press F2 to load default values and continue Anyway the info is as follows. American Megatrends Release 11/21/2001 AMIBIOS (C)2000 American Megatrends Inc. BIOS ver 2.09 NS570 KBC Version: 1.17 Pentium III,1GHz Checking NVRAM... 253952KB OK ICS9248-146 Inside WAIT.... CMOS Battery Low Press F1------- Press F2------- (C) American Megatrends Inc. 62-0213-009999-001010000-071595-SIS630-1AA0G008-W If I press F1 goes into BIOS. F2 load defualts and goes to page 2 of setup. Page 2: Main Processor :Pentium III Math Processor :Built-IN Base Mem Size : 640KB Floppy Drive A: :1.44 MB 31/2" Ext. mem Size : 247MB Floppy b none Seriall 3F8 Display Type VGA/EGA Parallel Port 378 AMIBIOS date 11/21/2001 Proc. Clock 1GHZ Exter. Cache 256KB, Enabled Power Mage. Enabled Hard Disk Cyl Head Sector Size LBA 32Bit Block PIO UDMA Mode Mode Mode Mode Mode Primary Master : 58140 16 63 30006MB LBA On 16Sec 4 4 Sec. Master : DVD-ROM 4 2 PCI Devices: Onboard IDE Onboard Comm. Device, IRQ10 Onboard Multimedia Dev. IRQ11 " USB Contr., IRQ9 " USB Control. IRQ9 " Ethernet, IRQ10 " PCI Bridge " CardBus Bridge Bridge VGA SDRAM at DIMM # :1 Invalid HIBERNATION partition/file...RUN HDPREPEZ... Do you want to (B)oot or (P)ower down? __ *** Not sure if any of this helps or not********** "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#14
|
|||
|
|||
invalid hibernation partition/file????
Under PM setup I have the following selections:
PM = enable or disabled Power Switch Type = Suspend on/off LID Switch Type = Screenoff / suspend Suspend mode = POS(S1) / Disable / STD(S4) Standby time out = Dis / 1 minute- 15 minutes Suspend Time out = Dis / 1min - 30 min HD time out = dis / 1 - 15 minutes Fan Mode = performance / Silent RTC Alarm = enabled / disabled RTC = Alarm date RTC = Hour RTC = Minute RTC = Second That's it under PM Setup. "Gary S. Terhune" none wrote in message ... I assume that when you choose Boot when asked at the end, nothing happens? CMOS battery low would explain the error message IF that Save to File or whatever setting existed. There's only one Power Management setting? It looks like it's enabled. It doesn't have any kind of sub-menu with a bunch of other PM-related settings? Did you try disabling PM? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Aas a followup. I pulled the battery and the startup stops on the first page asking for; Press F1 to run SETUP Press F2 to load default values and continue Anyway the info is as follows. American Megatrends Release 11/21/2001 AMIBIOS (C)2000 American Megatrends Inc. BIOS ver 2.09 NS570 KBC Version: 1.17 Pentium III,1GHz Checking NVRAM... 253952KB OK ICS9248-146 Inside WAIT.... CMOS Battery Low Press F1------- Press F2------- (C) American Megatrends Inc. 62-0213-009999-001010000-071595-SIS630-1AA0G008-W If I press F1 goes into BIOS. F2 load defualts and goes to page 2 of setup. Page 2: Main Processor :Pentium III Math Processor :Built-IN Base Mem Size : 640KB Floppy Drive A: :1.44 MB 31/2" Ext. mem Size : 247MB Floppy b none Seriall 3F8 Display Type VGA/EGA Parallel Port 378 AMIBIOS date 11/21/2001 Proc. Clock 1GHZ Exter. Cache 256KB, Enabled Power Mage. Enabled Hard Disk Cyl Head Sector Size LBA 32Bit Block PIO UDMA Mode Mode Mode Mode Mode Primary Master : 58140 16 63 30006MB LBA On 16Sec 4 4 Sec. Master : DVD-ROM 4 2 PCI Devices: Onboard IDE Onboard Comm. Device, IRQ10 Onboard Multimedia Dev. IRQ11 " USB Contr., IRQ9 " USB Control. IRQ9 " Ethernet, IRQ10 " PCI Bridge " CardBus Bridge Bridge VGA SDRAM at DIMM # :1 Invalid HIBERNATION partition/file...RUN HDPREPEZ... Do you want to (B)oot or (P)ower down? __ *** Not sure if any of this helps or not********** "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#15
|
|||
|
|||
invalid hibernation partition/file????
So I guess I may have screwed it up when I reinstalled win 98se which
included reformatting the HD. Oh well. It didn't ask for a partition other than 'normal' setup. And I didn't have any original disks. I may call a couple of shops around the area and see what they'd charge to look at it. I don't trust myself pulling it and putting in one of my systems. At least it didn't cost the Historical Society anything but it's a shame to dump it if it can be fixed. I want to thank you very much for all your help and suggestions. If it gets working I'll try and let you know. Thanks again, L. O'Fallon, XX H.S. "Gary S. Terhune" none wrote in message ... Well here's where we a Everything I can find on this message, which is common to many laptops that use the same Hibernation system... All roads lead to those same instructions you already tried. The file that the message suggests you run, if you could read the whole message, is "HDPREP (or HDPREPEZ), or 'AMI Save to File Utility'". That would prepare the hard drive by creating a special partition to hold Hibernation data. But you have to prep the HD *before* you turn on the feature, and you have to turn off the feature to make it let you boot if the HD isn't prepped properly. In short, I'm not sure I can take you any farther. If there is no possible power management option that fits the bill, I have to wonder if someone tried to update the BIOS and screwed up. I dunno, nothing quite makes sense. All I know is that it's the BIOS that's holding you up, and it's holding you up because it can't find the hibernation partition. Hmmm... I suppose you could try taking out the HD, putting it into a desktop, and run the HDPREP program, then put it back in the laptop. Would be a complicated operation (gotta make sure only the laptop HD gets "prepped", which might mean having to disable the rest of the HDs in the machine and use a bootable floppy setup disk to run the HDPREP utility. But it all comes back to BIOS should have that setting, and if it doesn't, nothing makes sense. Sorry, but I don't think I could come up with anything else without the machine in front of me. I'd want to take the disk out and put it into another machine to see what partitions there are, and I'd want to positively identify the motherboard and determine if it was possible to find a BIOS version for it that has the proper settings... Just doesn't make any sense. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#16
|
|||
|
|||
invalid hibernation partition/file????
Ummm.... Try tapping F8, or Ctrl, repeatedly as the system cranks up. Just
methodically tap the key from power on until a Startup Menu appears. If it does, post back. If it doesn't, try various times, using different tempos. Doesn't make sense that this would work if floppy can't boot, but it's desperation time. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#17
|
|||
|
|||
invalid hibernation partition/file????
Did you try disabling PM altogether?
-- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Under PM setup I have the following selections: PM = enable or disabled Power Switch Type = Suspend on/off LID Switch Type = Screenoff / suspend Suspend mode = POS(S1) / Disable / STD(S4) Standby time out = Dis / 1 minute- 15 minutes Suspend Time out = Dis / 1min - 30 min HD time out = dis / 1 - 15 minutes Fan Mode = performance / Silent RTC Alarm = enabled / disabled RTC = Alarm date RTC = Hour RTC = Minute RTC = Second That's it under PM Setup. "Gary S. Terhune" none wrote in message ... I assume that when you choose Boot when asked at the end, nothing happens? CMOS battery low would explain the error message IF that Save to File or whatever setting existed. There's only one Power Management setting? It looks like it's enabled. It doesn't have any kind of sub-menu with a bunch of other PM-related settings? Did you try disabling PM? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Aas a followup. I pulled the battery and the startup stops on the first page asking for; Press F1 to run SETUP Press F2 to load default values and continue Anyway the info is as follows. American Megatrends Release 11/21/2001 AMIBIOS (C)2000 American Megatrends Inc. BIOS ver 2.09 NS570 KBC Version: 1.17 Pentium III,1GHz Checking NVRAM... 253952KB OK ICS9248-146 Inside WAIT.... CMOS Battery Low Press F1------- Press F2------- (C) American Megatrends Inc. 62-0213-009999-001010000-071595-SIS630-1AA0G008-W If I press F1 goes into BIOS. F2 load defualts and goes to page 2 of setup. Page 2: Main Processor :Pentium III Math Processor :Built-IN Base Mem Size : 640KB Floppy Drive A: :1.44 MB 31/2" Ext. mem Size : 247MB Floppy b none Seriall 3F8 Display Type VGA/EGA Parallel Port 378 AMIBIOS date 11/21/2001 Proc. Clock 1GHZ Exter. Cache 256KB, Enabled Power Mage. Enabled Hard Disk Cyl Head Sector Size LBA 32Bit Block PIO UDMA Mode Mode Mode Mode Mode Primary Master : 58140 16 63 30006MB LBA On 16Sec 4 4 Sec. Master : DVD-ROM 4 2 PCI Devices: Onboard IDE Onboard Comm. Device, IRQ10 Onboard Multimedia Dev. IRQ11 " USB Contr., IRQ9 " USB Control. IRQ9 " Ethernet, IRQ10 " PCI Bridge " CardBus Bridge Bridge VGA SDRAM at DIMM # :1 Invalid HIBERNATION partition/file...RUN HDPREPEZ... Do you want to (B)oot or (P)ower down? __ *** Not sure if any of this helps or not********** "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#18
|
|||
|
|||
invalid hibernation partition/file????
Please do let us know if you figure it out. Wish I could get my hands on it.
'Course, then I wouldn't get the garden finished this week. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... So I guess I may have screwed it up when I reinstalled win 98se which included reformatting the HD. Oh well. It didn't ask for a partition other than 'normal' setup. And I didn't have any original disks. I may call a couple of shops around the area and see what they'd charge to look at it. I don't trust myself pulling it and putting in one of my systems. At least it didn't cost the Historical Society anything but it's a shame to dump it if it can be fixed. I want to thank you very much for all your help and suggestions. If it gets working I'll try and let you know. Thanks again, L. O'Fallon, XX H.S. "Gary S. Terhune" none wrote in message ... Well here's where we a Everything I can find on this message, which is common to many laptops that use the same Hibernation system... All roads lead to those same instructions you already tried. The file that the message suggests you run, if you could read the whole message, is "HDPREP (or HDPREPEZ), or 'AMI Save to File Utility'". That would prepare the hard drive by creating a special partition to hold Hibernation data. But you have to prep the HD *before* you turn on the feature, and you have to turn off the feature to make it let you boot if the HD isn't prepped properly. In short, I'm not sure I can take you any farther. If there is no possible power management option that fits the bill, I have to wonder if someone tried to update the BIOS and screwed up. I dunno, nothing quite makes sense. All I know is that it's the BIOS that's holding you up, and it's holding you up because it can't find the hibernation partition. Hmmm... I suppose you could try taking out the HD, putting it into a desktop, and run the HDPREP program, then put it back in the laptop. Would be a complicated operation (gotta make sure only the laptop HD gets "prepped", which might mean having to disable the rest of the HDs in the machine and use a bootable floppy setup disk to run the HDPREP utility. But it all comes back to BIOS should have that setting, and if it doesn't, nothing makes sense. Sorry, but I don't think I could come up with anything else without the machine in front of me. I'd want to take the disk out and put it into another machine to see what partitions there are, and I'd want to positively identify the motherboard and determine if it was possible to find a BIOS version for it that has the proper settings... Just doesn't make any sense. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#19
|
|||
|
|||
invalid hibernation partition/file????
Sure did.
Wondering if I should replace the CMOS battery or just put in shop? "Gary S. Terhune" none wrote in message ... Did you try disabling PM altogether? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Under PM setup I have the following selections: PM = enable or disabled Power Switch Type = Suspend on/off LID Switch Type = Screenoff / suspend Suspend mode = POS(S1) / Disable / STD(S4) Standby time out = Dis / 1 minute- 15 minutes Suspend Time out = Dis / 1min - 30 min HD time out = dis / 1 - 15 minutes Fan Mode = performance / Silent RTC Alarm = enabled / disabled RTC = Alarm date RTC = Hour RTC = Minute RTC = Second That's it under PM Setup. "Gary S. Terhune" none wrote in message ... I assume that when you choose Boot when asked at the end, nothing happens? CMOS battery low would explain the error message IF that Save to File or whatever setting existed. There's only one Power Management setting? It looks like it's enabled. It doesn't have any kind of sub-menu with a bunch of other PM-related settings? Did you try disabling PM? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Aas a followup. I pulled the battery and the startup stops on the first page asking for; Press F1 to run SETUP Press F2 to load default values and continue Anyway the info is as follows. American Megatrends Release 11/21/2001 AMIBIOS (C)2000 American Megatrends Inc. BIOS ver 2.09 NS570 KBC Version: 1.17 Pentium III,1GHz Checking NVRAM... 253952KB OK ICS9248-146 Inside WAIT.... CMOS Battery Low Press F1------- Press F2------- (C) American Megatrends Inc. 62-0213-009999-001010000-071595-SIS630-1AA0G008-W If I press F1 goes into BIOS. F2 load defualts and goes to page 2 of setup. Page 2: Main Processor :Pentium III Math Processor :Built-IN Base Mem Size : 640KB Floppy Drive A: :1.44 MB 31/2" Ext. mem Size : 247MB Floppy b none Seriall 3F8 Display Type VGA/EGA Parallel Port 378 AMIBIOS date 11/21/2001 Proc. Clock 1GHZ Exter. Cache 256KB, Enabled Power Mage. Enabled Hard Disk Cyl Head Sector Size LBA 32Bit Block PIO UDMA Mode Mode Mode Mode Mode Primary Master : 58140 16 63 30006MB LBA On 16Sec 4 4 Sec. Master : DVD-ROM 4 2 PCI Devices: Onboard IDE Onboard Comm. Device, IRQ10 Onboard Multimedia Dev. IRQ11 " USB Contr., IRQ9 " USB Control. IRQ9 " Ethernet, IRQ10 " PCI Bridge " CardBus Bridge Bridge VGA SDRAM at DIMM # :1 Invalid HIBERNATION partition/file...RUN HDPREPEZ... Do you want to (B)oot or (P)ower down? __ *** Not sure if any of this helps or not********** "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
#20
|
|||
|
|||
invalid hibernation partition/file????
Tried that also. no luck.
I'll play with it rest of day and to shop or ----.. Go and get your garden finished. With the rain we've had here in midwest, I haven't start. Flowers are in but no garden. Again Thanks "Gary S. Terhune" none wrote in message ... Ummm.... Try tapping F8, or Ctrl, repeatedly as the system cranks up. Just methodically tap the key from power on until a Startup Menu appears. If it does, post back. If it doesn't, try various times, using different tempos. Doesn't make sense that this would work if floppy can't boot, but it's desperation time. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Sorry for the delays, work. Not sure exactly what make this thing is.No markings on case. The only info is on a plate on bottom of system and it's stated "Personal Computer Model No. N340S8". Another problem is that this was donated and they isn't any disks, etc. that came with it. "Gary S. Terhune" none wrote in message ... What is the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L." wrote in message ... Followed your instructions but still no go. I went into BIOS and set floopy to be "1st Boot Device", inserted floppy and restarted system. After intitial startup, goes straight to error msg. "Gary S. Terhune" none wrote in message ... You run BOOTITNG.EXE on the system you used to download it, and it make's its own bootable floppy (or CD.) You then put that floppy in the problem machine and boot to it. Once it finishes loading, the first dialogue you get will be to install BootIt NG (BING) and that's where you Cancel the installation. Sorry for the less than clear instructions. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Here's what I've got. D/L and copied to a floppy BootItng.exe. (had to d/l on another system) Made a bootable floppy when I installed Win98se. Problem is, Iv'e set BIOS to read floppy 1st, Cd 2nd and then HD but this system isn't following instructions. When the system starts, I can't hear either disk running and then I get error msg. I'm confused, when you say to make a bootable floopy unless you're taking about something other than the one I create with win98se. Also, run Bootitng.exe--- how when the system locks up even though I have the bootable floopy in the drive. "Gary S. Terhune" none wrote in message ... Sorry, that download from BootIt NG is a ZIP file. Unzip that to a new folder and then run BOOTITNG.EXE file in that folder. -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "Gary S. Terhune" none wrote in message ... My suggestion is to get a copy of BootIt NG from www.bootitng.com. No need to pay, just download the EXE, make a bootable floppy or CD installer, reboot to the floppy or CD and then CANCEL THE INSTALLATION! That will drop you into Maintenance Mode where you can choose Partition Work. See what's listed there in the middle panel. More than just the one partition where you installed Win98? If so, please list them for us here, including name, size, type. What's the make/model of the machine? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Followed link. Problem is there is no such option. Nothing looks close to an auto Save-to-file option. "Gary S. Terhune" none wrote in message ... See he http://www.cybertechhelp.com/forums/...ad.php?t=33474 Let us know how it goes, OK? -- Gary S. Terhune MS-MVP Shell/User www.grystmill.com "L.S." wrote in message ... Received a donated laptop for our local historical society. Reformatted HD, everything worked/loaded, but when I restart system it locks up, no keyboard, nothing with the following msg. "Invalid hibernation partition/file run hd-----" I can get into BIOS, using Del key, but that's it. I've tried to use the startup floppy that was created during Win install but no go. I've put in the win98se cd and still nothing. Is this a win98se problem or did I do something? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
your hibernation file is missing or corrupted... | Jetson | General | 1 | February 6th 06 11:01 AM |
Hibernation | RMV | General | 3 | March 12th 05 08:09 PM |
Hibernation? | someone | General | 1 | September 26th 04 04:59 PM |
Hibernation | someone | General | 1 | September 25th 04 02:39 AM |
How to force driver to remount file system, when content of raw partition has changed?? | Egorov Dmitry | Disk Drives | 1 | July 20th 04 08:19 PM |