If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
RAM
I have a HP Pavilion 6511 Desktop with the following:
1. Motherboard - P5S-VM, Supplier -ASUS 2. Base Processor and Speed - 500 MHz AMD K6-2 with 3D Now! technology 3. Chipset - SiS 530 4. Memory - 64 MB SDRAM standard, Speed 100 MHz synchronous. As it has Three 168-pin DIMM sockets and can take upto 3X128 MB, I had added two more viz., a 64 and a 128 MB RAM's into the two vacant sockets. The unit was working well until recently when it had memory problems which I had ascertained using "Windows Memory Diagnostics". I wanted to verify my diagnosis and so I gave it to a service centre. They now advise me that the sockets are damaged and replacing with newer SDRAM also will NOT work and that I have live with the original 64 MB! Is there anyway to repair the DIMM sockets without having to replace the motherboard? In any case it will not be possible to obtain an outdated motherboard! Thanking you Capt K Ripendran |
#2
|
|||
|
|||
RAM
HP Pavilion PCs - Motherboard Specifications, P5S-VM (Osprey) -
http://h20000.www2.hp.com/bizsupport...ectID=bph04949 Exactly how did the service technician determine that the RAM sockets are damaged? When you installed the two additional DIMM sticks in the sockets, the system worked alright, with the additional RAM being recognised properly, for a period of time....correct? I am having a hard time accepting that the sockets are bad, unless they were physically damaged by inserting RAM backwards, with the notch not lined up with the key. EVEN if I accept their diagnosis without proof, you could still remove your original 64-MB stick, and insert a compatible 128-MB stick into that supposedly "good" socket, to give you 128MB RAM installed. So, their assertion that you are stuck with the original 64MB RAM just does not stand up. -- Glen Ventura, MS MVP Shell/User, A+ "Capt K Ripendran" wrote in message ... I have a HP Pavilion 6511 Desktop with the following: 1. Motherboard - P5S-VM, Supplier -ASUS 2. Base Processor and Speed - 500 MHz AMD K6-2 with 3D Now! technology 3. Chipset - SiS 530 4. Memory - 64 MB SDRAM standard, Speed 100 MHz synchronous. As it has Three 168-pin DIMM sockets and can take upto 3X128 MB, I had added two more viz., a 64 and a 128 MB RAM's into the two vacant sockets. The unit was working well until recently when it had memory problems which I had ascertained using "Windows Memory Diagnostics". I wanted to verify my diagnosis and so I gave it to a service centre. They now advise me that the sockets are damaged and replacing with newer SDRAM also will NOT work and that I have live with the original 64 MB! Is there anyway to repair the DIMM sockets without having to replace the motherboard? In any case it will not be possible to obtain an outdated motherboard! Thanking you Capt K Ripendran |
#3
|
|||
|
|||
RAM
The Tech advises me that placing the RAM in each of the DIMM socket, he was
able to determine that TWO were damaged as they did not recognise them although it worked for quite sometime. One of the reason I gave the machine to the Tech was because it was frequently going into fatal exception errors and hanging! I suppose, I will have to get a 128MB RAM and put it in one socket! Thanking you Regards Capt K Ripendran "glee" wrote in message ... HP Pavilion PCs - Motherboard Specifications, P5S-VM (Osprey) - http://h20000.www2.hp.com/bizsupport...ectID=bph04949 Exactly how did the service technician determine that the RAM sockets are damaged? When you installed the two additional DIMM sticks in the sockets, the system worked alright, with the additional RAM being recognised properly, for a period of time....correct? I am having a hard time accepting that the sockets are bad, unless they were physically damaged by inserting RAM backwards, with the notch not lined up with the key. EVEN if I accept their diagnosis without proof, you could still remove your original 64-MB stick, and insert a compatible 128-MB stick into that supposedly "good" socket, to give you 128MB RAM installed. So, their assertion that you are stuck with the original 64MB RAM just does not stand up. -- Glen Ventura, MS MVP Shell/User, A+ "Capt K Ripendran" wrote in message ... I have a HP Pavilion 6511 Desktop with the following: 1. Motherboard - P5S-VM, Supplier -ASUS 2. Base Processor and Speed - 500 MHz AMD K6-2 with 3D Now! technology 3. Chipset - SiS 530 4. Memory - 64 MB SDRAM standard, Speed 100 MHz synchronous. As it has Three 168-pin DIMM sockets and can take upto 3X128 MB, I had added two more viz., a 64 and a 128 MB RAM's into the two vacant sockets. The unit was working well until recently when it had memory problems which I had ascertained using "Windows Memory Diagnostics". I wanted to verify my diagnosis and so I gave it to a service centre. They now advise me that the sockets are damaged and replacing with newer SDRAM also will NOT work and that I have live with the original 64 MB! Is there anyway to repair the DIMM sockets without having to replace the motherboard? In any case it will not be possible to obtain an outdated motherboard! Thanking you Capt K Ripendran |
Thread Tools | |
Display Modes | |
|
|