A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows 98 » Networking
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Reminder on installing a NIC



 
 
Thread Tools Display Modes
  #1  
Old May 24th 06, 11:35 AM posted to microsoft.public.win98.networking
external usenet poster
 
Posts: n/a
Default Reminder on installing a NIC

The majority of the advice I found in
searching this newsgroup about how to
install a network interface card leads
to excessive optimism that Windows will
recognize new hardware.

So this is for the benefit of, you know,
the six people in the world who still
need to add an Ethernet card to a Windows
98 system. In my case, I want to download
software to an old 200MHz Pentium box to use
it as a dedicated controller of a digital
camera.

When I installed Windows 98 SE on a clean hard
drive, it never saw the NIC (an SMC EZ Card
1244) that was plugged in. When I subsequently
tried to use the "Add Hardware" icon, the
choices it presented, to make a long story short,
didn't provide for locating the drivers on
the CD-ROM that came with the card. I had
deleted all the stuff in the Network icon
list box that everybody says has to be deleted.
I had also gone to the System icon and
deleted everything under "Network adapters."
This didn't work, so I then pulled the card,
rebooted, replaced the card and rebooted, looking
for Windows to announce new hardware, which
it didn't.

Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.

--
Charles Packer
mailboxATcpacker.org
http://cpacker.org/whatnews

  #2  
Old May 24th 06, 05:48 PM posted to microsoft.public.win98.networking
external usenet poster
 
Posts: n/a
Default Reminder on installing a NIC

Although I didn't have the exact same problem, I can identify with what you
are saying and agree that 98SE seems to have a number of problems with NICS
and setting up Ethernet connections. I was also told that Windows will sort
it - wrong it didn't and revealed a known problem in this software of not
being able to find the drivers even though you tell it where they are
located. Anyway, I am going to upgrade to XP shortly - now that should be a
challenge!
Alan
wrote in message
oups.com...
The majority of the advice I found in
searching this newsgroup about how to
install a network interface card leads
to excessive optimism that Windows will
recognize new hardware.

So this is for the benefit of, you know,
the six people in the world who still
need to add an Ethernet card to a Windows
98 system. In my case, I want to download
software to an old 200MHz Pentium box to use
it as a dedicated controller of a digital
camera.

When I installed Windows 98 SE on a clean hard
drive, it never saw the NIC (an SMC EZ Card
1244) that was plugged in. When I subsequently
tried to use the "Add Hardware" icon, the
choices it presented, to make a long story short,
didn't provide for locating the drivers on
the CD-ROM that came with the card. I had
deleted all the stuff in the Network icon
list box that everybody says has to be deleted.
I had also gone to the System icon and
deleted everything under "Network adapters."
This didn't work, so I then pulled the card,
rebooted, replaced the card and rebooted, looking
for Windows to announce new hardware, which
it didn't.

Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.

--
Charles Packer
mailboxATcpacker.org
http://cpacker.org/whatnews



  #3  
Old May 24th 06, 05:48 PM posted to microsoft.public.win98.networking
Alan
External Usenet User
 
Posts: 213
Default Reminder on installing a NIC

Although I didn't have the exact same problem, I can identify with what you
are saying and agree that 98SE seems to have a number of problems with NICS
and setting up Ethernet connections. I was also told that Windows will sort
it - wrong it didn't and revealed a known problem in this software of not
being able to find the drivers even though you tell it where they are
located. Anyway, I am going to upgrade to XP shortly - now that should be a
challenge!
Alan
wrote in message
oups.com...
The majority of the advice I found in
searching this newsgroup about how to
install a network interface card leads
to excessive optimism that Windows will
recognize new hardware.

So this is for the benefit of, you know,
the six people in the world who still
need to add an Ethernet card to a Windows
98 system. In my case, I want to download
software to an old 200MHz Pentium box to use
it as a dedicated controller of a digital
camera.

When I installed Windows 98 SE on a clean hard
drive, it never saw the NIC (an SMC EZ Card
1244) that was plugged in. When I subsequently
tried to use the "Add Hardware" icon, the
choices it presented, to make a long story short,
didn't provide for locating the drivers on
the CD-ROM that came with the card. I had
deleted all the stuff in the Network icon
list box that everybody says has to be deleted.
I had also gone to the System icon and
deleted everything under "Network adapters."
This didn't work, so I then pulled the card,
rebooted, replaced the card and rebooted, looking
for Windows to announce new hardware, which
it didn't.

Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.

--
Charles Packer
mailboxATcpacker.org
http://cpacker.org/whatnews



  #4  
Old May 24th 06, 05:51 PM posted to microsoft.public.win98.networking
external usenet poster
 
Posts: n/a
Default Reminder on installing a NIC

Although I didn't have the exact same problem, I can identify with what you
are saying and agree that 98SE seems to have a number of problems with NICS
and setting up Ethernet connections. I was also told that Windows will sort
it - wrong it didn't and revealed a known problem in this software of not
being able to find the drivers even though you tell it where they are
located. Anyway, I am going to upgrade to XP shortly - now that should be a
challenge!
Alan
wrote in message
oups.com...
The majority of the advice I found in
searching this newsgroup about how to
install a network interface card leads
to excessive optimism that Windows will
recognize new hardware.

So this is for the benefit of, you know,
the six people in the world who still
need to add an Ethernet card to a Windows
98 system. In my case, I want to download
software to an old 200MHz Pentium box to use
it as a dedicated controller of a digital
camera.

When I installed Windows 98 SE on a clean hard
drive, it never saw the NIC (an SMC EZ Card
1244) that was plugged in. When I subsequently
tried to use the "Add Hardware" icon, the
choices it presented, to make a long story short,
didn't provide for locating the drivers on
the CD-ROM that came with the card. I had
deleted all the stuff in the Network icon
list box that everybody says has to be deleted.
I had also gone to the System icon and
deleted everything under "Network adapters."
This didn't work, so I then pulled the card,
rebooted, replaced the card and rebooted, looking
for Windows to announce new hardware, which
it didn't.

Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.

--
Charles Packer
mailboxATcpacker.org
http://cpacker.org/whatnews




  #5  
Old May 24th 06, 05:51 PM posted to microsoft.public.win98.networking
Alan
External Usenet User
 
Posts: 213
Default Reminder on installing a NIC

Although I didn't have the exact same problem, I can identify with what you
are saying and agree that 98SE seems to have a number of problems with NICS
and setting up Ethernet connections. I was also told that Windows will sort
it - wrong it didn't and revealed a known problem in this software of not
being able to find the drivers even though you tell it where they are
located. Anyway, I am going to upgrade to XP shortly - now that should be a
challenge!
Alan
wrote in message
oups.com...
The majority of the advice I found in
searching this newsgroup about how to
install a network interface card leads
to excessive optimism that Windows will
recognize new hardware.

So this is for the benefit of, you know,
the six people in the world who still
need to add an Ethernet card to a Windows
98 system. In my case, I want to download
software to an old 200MHz Pentium box to use
it as a dedicated controller of a digital
camera.

When I installed Windows 98 SE on a clean hard
drive, it never saw the NIC (an SMC EZ Card
1244) that was plugged in. When I subsequently
tried to use the "Add Hardware" icon, the
choices it presented, to make a long story short,
didn't provide for locating the drivers on
the CD-ROM that came with the card. I had
deleted all the stuff in the Network icon
list box that everybody says has to be deleted.
I had also gone to the System icon and
deleted everything under "Network adapters."
This didn't work, so I then pulled the card,
rebooted, replaced the card and rebooted, looking
for Windows to announce new hardware, which
it didn't.

Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.

--
Charles Packer
mailboxATcpacker.org
http://cpacker.org/whatnews




  #6  
Old May 27th 06, 01:19 PM posted to microsoft.public.win98.networking
external usenet poster
 
Posts: n/a
Default Reminder on installing a NIC

snip


Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.




all you would have to have done at that point
would have been "update drivers"


  #7  
Old May 27th 06, 01:19 PM posted to microsoft.public.win98.networking
philo
External Usenet User
 
Posts: 1,318
Default Reminder on installing a NIC

snip


Finally I found a posting that mentioned
the "PCI Ethernet Controller." I went to
the System icon again, found it lurking
in the device lineup, and deleted it.
This did it. I didn't even have to reboot.
I simply used the "Add hardware" icon, which this
time gave me a series of pop-ups that identified
the card and allowed me to designate the CD-ROM
as the source for the driver. When this sequence
was finished, I used the Run widget to execute winipcfg
to release and refresh the IP, and I was on-line.




all you would have to have done at that point
would have been "update drivers"


 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Installing WinXP on a disk partition Bob General 4 November 15th 05 01:08 AM
Problems Installing Win98SE MacKenrick General 3 July 13th 05 03:07 AM
Problem with Installing USB2.0/1394 Firewire Combo Card in Win ME Finnkai General 1 April 9th 05 01:00 AM
Registry Problem while installing Win98 Second Edition sudhi Setup & Installation 1 July 15th 04 05:06 PM
Adding new hardware stops responding when installing drivers JK Hardware 3 June 8th 04 04:44 PM


All times are GMT +1. The time now is 06:36 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2004-2018 Win98banter.
The comments are property of their posters.