If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
While installing Windows ME on a dual boot, system halted.
I have Windows XP installed on drive 0, partition 1, formatted ntfs. I have
formatted partition 3 as fat32 and made it primary as well (partition 2 is ntfs). I have a 2nd hard drive that is a sata with 2 partitions formatted ntfs. I am using a boot manager called "Graphical Boot manager" or GAG. I set it to boot to my fat32 drive and proceeeded to install Windows ME on that drive. During setup, when it tries to reboot for the 1st time, I get the error "Cannot find or load krnl386.exe, access to the file denied, system halted" I booted to XP and copied the file to the root folder and to the \windows folder. When I tried to boot ME again I received the same message again. I have an ASUS K8V deluxe motherboard with an AMD 64 3200+ processor and 1.5 GB Ram. Anyone have any suggestions? Thank You Kevin Nielsen |
#3
|
|||
|
|||
While installing Windows ME on a dual boot, system halted.
I tried to find info about cross post but could find nothing. Can you
direct me to a place where I can learn how to cross post? Thank You Kevin "Mike M" wrote in message ... Anyone have any suggestions? If posting to multiple newsgroups may I suggest you learn to cross post correctly rather than posting similar different messages to multiple groups. This helps you keep track of the replies whilst also helping those who might be in a position to help. Answered in the Win Me setup newsgroup. -- Mike Maltby MS-MVP Windows [2001-2006] Kevin J. Nielsen wrote: I have Windows XP installed on drive 0, partition 1, formatted ntfs. I have formatted partition 3 as fat32 and made it primary as well (partition 2 is ntfs). I have a 2nd hard drive that is a sata with 2 partitions formatted ntfs. I am using a boot manager called "Graphical Boot manager" or GAG. I set it to boot to my fat32 drive and proceeeded to install Windows ME on that drive. During setup, when it tries to reboot for the 1st time, I get the error "Cannot find or load krnl386.exe, access to the file denied, system halted" I booted to XP and copied the file to the root folder and to the \windows folder. When I tried to boot ME again I received the same message again. I have an ASUS K8V deluxe motherboard with an AMD 64 3200+ processor and 1.5 GB Ram. Anyone have any suggestions? |
#4
|
|||
|
|||
While installing Windows ME on a dual boot, system halted.
Kevin,
When using an NNTP news client such as Outlook Express which I see you are using, add the two or three newsgroups to which you want to post your message to the Newsgroups list in the message header. Your message will then be posted to all of those newsgroups and replies posted to that message in any of those newsgroups will be seen in all the others to which the original was cross posted - that is unless the person replying to the post decides to manually removes the cross-posting. Note also that a message when read in one of those newsgroups will then appear as "read" in all of the other groups to which it was cross-posted. There is an extension to this which is to cross-post the initial message but to then put just one newsgroup in the Followup-To field in the message header. Then when someone replies to the cross posted message all of the replies end up in a single newsgroup. The problem here however is that those not watching the newsgroup used for the Followup posts don't get to see the replies or even realise that the initial post has had replies. -- Mike Maltby MS-MVP Windows [2001-2006] Kevin J. Nielsen wrote: I tried to find info about cross post but could find nothing. Can you direct me to a place where I can learn how to cross post? Thank You |
#5
|
|||
|
|||
While installing Windows ME on a dual boot, system halted.
Thank you Mike for taking the time to answer my question personally
Kevin "Mike M" wrote in message ... Kevin, When using an NNTP news client such as Outlook Express which I see you are using, add the two or three newsgroups to which you want to post your message to the Newsgroups list in the message header. Your message will then be posted to all of those newsgroups and replies posted to that message in any of those newsgroups will be seen in all the others to which the original was cross posted - that is unless the person replying to the post decides to manually removes the cross-posting. Note also that a message when read in one of those newsgroups will then appear as "read" in all of the other groups to which it was cross-posted. There is an extension to this which is to cross-post the initial message but to then put just one newsgroup in the Followup-To field in the message header. Then when someone replies to the cross posted message all of the replies end up in a single newsgroup. The problem here however is that those not watching the newsgroup used for the Followup posts don't get to see the replies or even realise that the initial post has had replies. -- Mike Maltby MS-MVP Windows [2001-2006] Kevin J. Nielsen wrote: I tried to find info about cross post but could find nothing. Can you direct me to a place where I can learn how to cross post? Thank You |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
SECURITY ?? !!! ??? .... | RJK | General | 54 | February 5th 06 09:39 PM |
Win98SE constant problems-ole32,shell32,other | MEB | General | 14 | January 15th 06 04:39 AM |
Unable to boot dual boot system | M Jones | General | 3 | November 6th 05 10:23 AM |
Can't connect to my network printer | Martin Healy | Networking | 8 | July 6th 05 10:35 PM |
What is going on? | BAP | General | 20 | March 11th 05 12:25 PM |