If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
reinstalling 98se???
"L." wrote in message ... OK, that's the easy half. What happened to the PNP/PCI Configuration page? And Integrated Preipherals? -- Gary S. Terhune MS MVP Shell/User Here goes. PNP/PCI CONFIG. PNP OS installed: no OK for now, though you might change it to Yes later on. Reset config. data: no I'd try changking this to Yes. It's a one-off setting that gets executed during the next startup, causing BIOS to fully redetect and recinfigure devices. It will say No the next time you look. VA boot from: agp IIRC, you're now using a PCI video adapter. Change this to PCI. PCI vga palette snoop: Disable PCI slot 1/5 IRQ Pri.: auto " " 2 " " : auto " " 3 " " : auto " " 4 " " : auto IRQ 3: PCI/Pnp 4: " 5: " 7: " 9: " 10: " 11: " 14: " 15: " I don't want to get involved in micro-managing IRQs, and it shouldn't be necessary if you've stripped the system to minimums and disabled onboard sound (see below.) INTEGRATED PERIF. Enhanced ATAPI perf.: Disable Might try enabling this, as it directly affects the CD drive and you're having trouble with that. I'd try it, anyway. On board IDE: both IDE1 cond. cable: auto IDE2 cond. cable: auto onboard FDC: auto onboard serial porta: auto onboard serail portb: auto serial portb mode: normal duplex mode: n/a onboard parallel port: auto parallel port mode; ECP parallel port IRQ: auto parallel port DMA: auto ac97 audio: auto onboard legacy audio: enable I'd disable audio until you get Windows installed. soundblaster: disable sb i/o base address: 220h-22fh sb irq select: 5 sb dma select: 1 mpu-401 : disable mpu-401 i/o address: 330h-333h fm port (388h-38bh): disable game port(200h-207h): enable I'd also disable the game controller until Windows has been installed. Now I have another problem. Came in this morning, turned on system with floppy in. selected start with cdrom support and the system is freezing at: This driver is provided by Oak Tech., Inc. OTI-91x ATAPI cd=rom devise driver Rev. D9wv352 copyright-----.... Device name :OEMCD001 (this is where it stopping) I've tried 3 different cd-roms and switched cables. and checked master/slave switches. Well, if it's not due to a corrupt floppy disk, it unfortunately sounds like you may have a broken motherboard. Do you have any bootable CDs? If you have access to a CD burner, you can make your own bootable CD version of the Windows Startup disk. -- Gary S. Terhune MS MVP Shell/User |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Window updates after reinstalling Windows 98SE | Angel | General | 9 | November 29th 04 02:19 AM |
Problems after reinstalling WIN 98SE | X5aces | General | 2 | July 16th 04 03:17 PM |
reinstalling 98se | cliff | Setup & Installation | 1 | July 1st 04 02:25 PM |
Need Dual-booting info: current 98se & add xp | [email protected] | General | 4 | June 23rd 04 04:55 PM |
Reinstalling 98SE from upgrade CD? | KSM | General | 2 | June 15th 04 11:28 PM |