If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
2 computers together
A PCMCIA card is a way to plug in any number of items to a laptop. It's like
a PCI slot in a desktop machine. What you probably want is a PCMCIA Ethernet adapter that you can plug into that slot, and a cable to connect it to the router. Here are some examples http://tinyurl.com/2lpsbp If your router was wireless, then I would recommend a PCMCIA wireless adapter instead of a PCMCIA Ethernet (hardwired LAN) adapter. http://tinyurl.com/2jxmbq However, this would also require that you purchase a wireless gateway to connect to the router. Not cheap, unless you can convince your cable company to upgrade you to some sort of combination modem/router/wireless for not too much. http://tinyurl.com/3dsq28 Note that there are also PCMCIA USB cards available. For network connection, I'd much prefer the LAN or wireless option, since USB cables are much more expensive. Your router would also require a USB output, which many do, or I *think* there's a way to do "Direct Cable Connection" to the desktop using USB, but it's by far the more limited option. Considering what you say you have now, a PCMCIA Ethernet adapter and a decent length of Ethernet cable is by far the cheapest solution, and it happens to also be the easiest to set up. Wireless would be the most convenient solution, since it allows the laptop to go anywhere in the house or yard. It's also the most expensive, by far. USB is probably the least convenient and the hardest to set up, but if you were to replace your router with one that had USB output, the PCMCIA card could then double for any number of other USB purposes. Considering how relatively inexpensive PCMCIA cards are, I'd suggest just getting one if you need it, and leaving it out of the networking equation. -- Gary S. Terhune MS-MVP Shell/User "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb "Ron Badour" wrote: The easy way to transfer games is to use a memory stick providing your laptop has a USB port. -- Regards Ron Badour, MS MVP for W98 Tips: http://home.satx.rr.com/badour Knowledge Base Info: http://support.microsoft.com/default.aspx?pr=kbinfo "breezyyb" wrote in message ... very sorry it has taken so long to reply...what I would like to do is hook the 2 computers together and try and get the laptop online. what does it have?? its got a PMCIA card and thats it, its set up for dialup and I have cable. it doesnt have a cd rom. I would like to get a few games on it that are already on my desktop, like gamehouse,solitaire,etc....I guess transferr them would be a better term. and about getting it online, I guess I just wanted to know if you can do that sort of thing...so thats not at the top of the list for me...I dont know if I know what to do or what to hook together with what cords..serial port,com port...I am just a bit befuddled. so I hope this answered all the things you asked, (and I had left out in the begining!! sorry) I hope to hear from someone soon, but its not an emergency...whenever you guys have the time!! thanks again!! breezyyb~~pennie |
#12
|
|||
|
|||
2 computers together
What does the label on the PCMCIA card say? It could be a modem, an
Ethernet card, memory or a number of other things. -- Jeff Richards MS MVP (Windows - Shell/User) "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb |
#13
|
|||
|
|||
2 computers together
hi again...
the card that was in the laptop is a "data/fax modem...PCMCIA from IBM"...there is nothing but the card...nothing attched to it. so I went out and got this "D-Link 10/100 fast ethernet notebook adapter"...and guess what? I cant install the thing because I dont have a cd-rom inthe laptop...I think I am about to give up here!! I seem to be getting beat all the way around! If you have no more ideas that all right...I did put the card into the laptop, and it fits nicly but there it sits and nothing happened when its hooked up to the internet....the laptop doesnt even seem to recognize it the card, but I was hoping something good would happen!! I have hit a dead end huh? thanks for all your help!!! pennie "Jeff Richards" wrote: What does the label on the PCMCIA card say? It could be a modem, an Ethernet card, memory or a number of other things. -- Jeff Richards MS MVP (Windows - Shell/User) "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb |
#14
|
|||
|
|||
2 computers together
Haven't even come *close* to a dead end, yet.
The drivers required by a PCMCIA network adapter should fit on a floppy. The laptop has a floppy drive, doesn't it? Alternatively, the laptop now has a modem, which means you can make a dial-up connection to the internet, which means you can download the drivers package from D-Link if they won't fit onto a floppy, or perhaps you can do it using two floppies. Certainly shouldn't require more than that. What model is your D-Link card? Who do you get your internet service from? With those two answers, especially the first one, I can almost certainly come up with a way for you to install your D-Link card. -- Gary S. Terhune MS-MVP Shell/User "breezyyb" wrote in message ... hi again... the card that was in the laptop is a "data/fax modem...PCMCIA from IBM"...there is nothing but the card...nothing attched to it. so I went out and got this "D-Link 10/100 fast ethernet notebook adapter"...and guess what? I cant install the thing because I dont have a cd-rom inthe laptop...I think I am about to give up here!! I seem to be getting beat all the way around! If you have no more ideas that all right...I did put the card into the laptop, and it fits nicly but there it sits and nothing happened when its hooked up to the internet....the laptop doesnt even seem to recognize it the card, but I was hoping something good would happen!! I have hit a dead end huh? thanks for all your help!!! pennie "Jeff Richards" wrote: What does the label on the PCMCIA card say? It could be a modem, an Ethernet card, memory or a number of other things. -- Jeff Richards MS MVP (Windows - Shell/User) "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb |
#15
|
|||
|
|||
2 computers together
ok...we're not dead yet...the model # of the D-Link is DFE-690TXD. and I have
my service from our cable company, mediacom. we have NO dial up here in the house...we dont even have a house phone!! hope that will help you to help me...THANKS!!! pennie "Gary S. Terhune" wrote: Haven't even come *close* to a dead end, yet. The drivers required by a PCMCIA network adapter should fit on a floppy. The laptop has a floppy drive, doesn't it? Alternatively, the laptop now has a modem, which means you can make a dial-up connection to the internet, which means you can download the drivers package from D-Link if they won't fit onto a floppy, or perhaps you can do it using two floppies. Certainly shouldn't require more than that. What model is your D-Link card? Who do you get your internet service from? With those two answers, especially the first one, I can almost certainly come up with a way for you to install your D-Link card. -- Gary S. Terhune MS-MVP Shell/User "breezyyb" wrote in message ... hi again... the card that was in the laptop is a "data/fax modem...PCMCIA from IBM"...there is nothing but the card...nothing attched to it. so I went out and got this "D-Link 10/100 fast ethernet notebook adapter"...and guess what? I cant install the thing because I dont have a cd-rom inthe laptop...I think I am about to give up here!! I seem to be getting beat all the way around! If you have no more ideas that all right...I did put the card into the laptop, and it fits nicly but there it sits and nothing happened when its hooked up to the internet....the laptop doesnt even seem to recognize it the card, but I was hoping something good would happen!! I have hit a dead end huh? thanks for all your help!!! pennie "Jeff Richards" wrote: What does the label on the PCMCIA card say? It could be a modem, an Ethernet card, memory or a number of other things. -- Jeff Richards MS MVP (Windows - Shell/User) "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb |
#16
|
|||
|
|||
2 computers together
OK, using your XP machine go he
http://support.dlink.com/products/vi...690TXD#drivers (If that doesn't work in your email client, click he http://tinyurl.com/27fxbd) In the box that says "Drivers", click on the "98" icon. That should open a small window that describes the driver download. Click on "Download". That will start a download. Save it to your Desktop, or better yet, you should create a folder on C:\ called "Downloads", another folder inside that one called "98 Laptop", another inside that called "D-Link", and save the download to that folder. I save all drivers and other downloads to a Downloads folder, using a well structured set of folders. Makes them easy to find later. Copy that downloaded EXE to a floppy to transfer to your laptop. It's only 84 KB. Copy the file from the floppy drive to another new set of folders resembling the one above. Double-click it, and when prompted where to save the files, click Browse and browse to the folder where you saved the EXE file. DO NOT save to the TEMP folder as prompted. Shut down the system, insert the card, then restart. Windows should detect the new hardware during startup and prompt you to install it. Click Next, choose "Search for best driver...", then Next. On the next dialogue, uncheck everything except "Specify location", then use the Browse to browse to the location where you unpacked the files earlier, going one step further and clicking on the WIN98 folder that is now there. If there aren't any driver installation files in the folder, it won't let you click OK. Then click on through to finish the process. You will also need to have your original Windows 98 installation files available, but I'm betting they're already on your system, and Windows will automatically locate them. You'll have to restart your system for everything to work. Make sure to connect the cable to the router, also. If you can't then connect to the internet, use the StartRun box to run WINIPCFG. Click Release All, then Renew All. Try the internet again. If you still have no luck, go to Network applet in Control Panel and tell us what's listed there. -- Gary S. Terhune MS MVP -- Shell/User http://grystmill.com/articles/cleanboot.htm http://grystmill.com/articles/security.htm "breezyyb" wrote in message ... ok...we're not dead yet...the model # of the D-Link is DFE-690TXD. and I have my service from our cable company, mediacom. we have NO dial up here in the house...we dont even have a house phone!! hope that will help you to help me...THANKS!!! pennie "Gary S. Terhune" wrote: Haven't even come *close* to a dead end, yet. The drivers required by a PCMCIA network adapter should fit on a floppy. The laptop has a floppy drive, doesn't it? Alternatively, the laptop now has a modem, which means you can make a dial-up connection to the internet, which means you can download the drivers package from D-Link if they won't fit onto a floppy, or perhaps you can do it using two floppies. Certainly shouldn't require more than that. What model is your D-Link card? Who do you get your internet service from? With those two answers, especially the first one, I can almost certainly come up with a way for you to install your D-Link card. -- Gary S. Terhune MS-MVP Shell/User "breezyyb" wrote in message ... hi again... the card that was in the laptop is a "data/fax modem...PCMCIA from IBM"...there is nothing but the card...nothing attched to it. so I went out and got this "D-Link 10/100 fast ethernet notebook adapter"...and guess what? I cant install the thing because I dont have a cd-rom inthe laptop...I think I am about to give up here!! I seem to be getting beat all the way around! If you have no more ideas that all right...I did put the card into the laptop, and it fits nicly but there it sits and nothing happened when its hooked up to the internet....the laptop doesnt even seem to recognize it the card, but I was hoping something good would happen!! I have hit a dead end huh? thanks for all your help!!! pennie "Jeff Richards" wrote: What does the label on the PCMCIA card say? It could be a modem, an Ethernet card, memory or a number of other things. -- Jeff Richards MS MVP (Windows - Shell/User) "breezyyb" wrote in message ... hi again..ok, upon looking at the laptop, it has no USB port...(GASP!)...all it has is the PMCIA card which I assume should have some sort of wire/cord attached. my desktop has the modem and router that Mr. Terhune described. we are hooked up to with our cable company... I do really apologize for not giving all this info to start with...I thought it would just be a matter of hooking up a serial port cable and off I would go!! wow! but thanks again for taking the time...breezyyb |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
how to conect two computers to the internet | [email protected] | Networking | 6 | January 1st 07 12:39 AM |
Cannot connect to other computers | LadyJR | Networking | 4 | July 7th 06 12:29 PM |
importing/exporting user data across all computers in network? HEL | carlos | General | 0 | January 17th 05 05:21 PM |
Computers on network don't communicate | Trish | General | 3 | November 21st 04 04:01 AM |
Can't see all computers on one computer | mcavoym1 | Networking | 2 | November 9th 04 07:57 AM |