If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
start > run
When I enter netstat -an, the screen literally flashes for a split second and vanishes. Why? Practice safe eating - always use condiments |
#2
|
|||
|
|||
start > run
You have to open a command prompt first. Netstat is a commandline utility, not a windowing
GUI utility. Go to; Start -- run execute; command.com Now execute; netstat -an Dave "sf" wrote in message ... | | When I enter netstat -an, the screen literally flashes for a | split second and vanishes. Why? | | | Practice safe eating - always use condiments |
#3
|
|||
|
|||
start > run
If you use netstat with parameters from Start Run, it will flash a DOS box and
close. Run it from Start Programs MS-DOS Prompt. Here are the available parameters, which can be seen by typing: netstat /? at the DOS prompt - NETSTAT [-a] [-e] [-n] [-s] [-p proto] [-r] [interval] -a Displays all connections and listening ports. -e Displays Ethernet statistics. This may be combined with the -s option. -n Displays addresses and port numbers in numerical form. -p proto Shows connections for the protocol specified by proto; proto may be TCP or UDP. If used with the -s option to display per-protocol statistics, proto may be TCP, UDP, or IP. -r Displays the routing table. -s Displays per-protocol statistics. By default, statistics are shown for TCP, UDP and IP; the -p option may be used to specify a subset of the default. interval Redisplays selected statistics, pausing interval seconds between each display. Press CTRL+C to stop redisplaying statistics. If omitted, netstat will print the current configuration information once. -- Glen Ventura, MS MVP W95/98 Systems http://dts-l.org/goodpost.htm "sf" wrote in message ... When I enter netstat -an, the screen literally flashes for a split second and vanishes. Why? Practice safe eating - always use condiments |
#4
|
|||
|
|||
start > run
Thanks, Glee!
```````````` On Mon, 19 Jul 2004 22:25:24 -0400, "glee" wrote: If you use netstat with parameters from Start Run, it will flash a DOS box and close. Run it from Start Programs MS-DOS Prompt. Here are the available parameters, which can be seen by typing: netstat /? at the DOS prompt - NETSTAT [-a] [-e] [-n] [-s] [-p proto] [-r] [interval] -a Displays all connections and listening ports. -e Displays Ethernet statistics. This may be combined with the -s option. -n Displays addresses and port numbers in numerical form. -p proto Shows connections for the protocol specified by proto; proto may be TCP or UDP. If used with the -s option to display per-protocol statistics, proto may be TCP, UDP, or IP. -r Displays the routing table. -s Displays per-protocol statistics. By default, statistics are shown for TCP, UDP and IP; the -p option may be used to specify a subset of the default. interval Redisplays selected statistics, pausing interval seconds between each display. Press CTRL+C to stop redisplaying statistics. If omitted, netstat will print the current configuration information once. Practice safe eating - always use condiments |
#5
|
|||
|
|||
start > run
On Mon, 19 Jul 2004 16:57:11 -0400, "David H. Lipman"
wrote: You have to open a command prompt first. Netstat is a commandline utility, not a windowing GUI utility. Go to; Start -- run execute; command.com Now execute; netstat -an Thanks, Dave... it worked perfectly! I was able to use the print screen button and pasted the information into word to analyze it. I'm trying to educate myself about ports. How do I tell from those numbers which port is open on my computer? I was trying to find port 5180, the one that Netscape uses (I am assuming that Mozilla/Firefox use the same port). For instance, I think Established means a port is open... but which one? Is it the number following the : in the left column? I also know that 127.0.0.1 is my computer, so I'm assuming ZA is doing its job. TCP 127.0.0.1:1152 127.0.0.1:1153 ESTABLISHED TCP 127.0.0.1:1153 127.0.0.1:1152 ESTABLISHED TCP 127.0.0.1:143 0.0.0.0:0 LISTENING TCP 192.168.250.3:1151 204.127.204.17:119 ESTABLISHED TCP 192.168.250.3:1164 209.247.153.137:80 ESTABLISHED TCP 192.168.250.3:1165 209.247.153.137:80 ESTABLISHED TIA Practice safe eating - always use condiments |
#6
|
|||
|
|||
start > run
A better utility to use is TCPVIEW.EXE -- free from SysInternals @
http://www.sysinternals.com/ntw2k/source/tcpview.shtml It is a GUI utility. Dave "sf" wrote in message news | On Mon, 19 Jul 2004 16:57:11 -0400, "David H. Lipman" | wrote: | | You have to open a command prompt first. Netstat is a commandline utility, not a windowing | GUI utility. | | Go to; Start -- run | execute; command.com | | Now execute; netstat -an | | Thanks, Dave... it worked perfectly! I was able to use the | print screen button and pasted the information into word to | analyze it. | | I'm trying to educate myself about ports. How do I tell | from those numbers which port is open on my computer? I was | trying to find port 5180, the one that Netscape uses (I am | assuming that Mozilla/Firefox use the same port). | | For instance, I think Established means a port is open... | but which one? Is it the number following the : in the left | column? I also know that 127.0.0.1 is my computer, so I'm | assuming ZA is doing its job. | | TCP 127.0.0.1:1152 127.0.0.1:1153 ESTABLISHED | TCP 127.0.0.1:1153 127.0.0.1:1152 ESTABLISHED | TCP 127.0.0.1:143 0.0.0.0:0 LISTENING | TCP 192.168.250.3:1151 204.127.204.17:119 ESTABLISHED | TCP 192.168.250.3:1164 209.247.153.137:80 ESTABLISHED | TCP 192.168.250.3:1165 209.247.153.137:80 ESTABLISHED | | TIA | | | | | Practice safe eating - always use condiments |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Start Vs. Restart | JD | General | 11 | July 7th 04 08:11 PM |
start up problems | mike | General | 2 | July 6th 04 07:18 PM |
Win98 won't start after a fresh reload - issue with a video driver? | John D | General | 1 | July 1st 04 03:33 PM |
How to start Windows without loading programs? | Glenn | General | 3 | June 27th 04 12:22 PM |
how to use start up disc created with 98 2nd edition update | howard | General | 9 | June 12th 04 09:07 PM |