If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Bios problem
I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a
program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I never see any information. I have researched these beep codes and read posts describing securing the video card cables/connections, but I have a chipset that I did actually assure is snug to the motherboard. This generated no change. Does anyone have an idea as to a next step? -- Bob K |
#2
|
|||
|
|||
Bios problem
"bobk" wrote in message news I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I never see any information. I have researched these beep codes and read posts describing securing the video card cables/connections, but I have a chipset that I did actually assure is snug to the motherboard. This generated no change. Does anyone have an idea as to a next step? first off, you did not tell us what your manual said the beep codes mean... however for the most part the two big possibilities are video or ram... so you should remove your ram and video card and reseat it and try again. |
#3
|
|||
|
|||
Bios problem
"bobk" wrote in message
news I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I 1. Whether your monitor hardware is OK or not, you cannot damage it by uninstaling software from the main board. To test your monitor, exchange it for a monitor known to be working OK. If you get the same results, the fault is in the PC. 2. You need to find out the meaning of the POST sound codes. -- Don Phillipson Carlsbad Springs (Ottawa, Canada) |
#4
|
|||
|
|||
Bios problem
There is no video "card", it is a small box. Should I try removing that?
-- Bob K "philo" wrote: "bobk" wrote in message news I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I never see any information. I have researched these beep codes and read posts describing securing the video card cables/connections, but I have a chipset that I did actually assure is snug to the motherboard. This generated no change. Does anyone have an idea as to a next step? first off, you did not tell us what your manual said the beep codes mean... however for the most part the two big possibilities are video or ram... so you should remove your ram and video card and reseat it and try again. |
#5
|
|||
|
|||
Bios problem
"bobk" wrote in message ... There is no video "card", it is a small box. Should I try removing that? -- Bob K if it's "on-board" video don't fool with it... it's probably a ram error... but you better consult your manual!@!! |
#6
|
|||
|
|||
Bios problem
Check your ram modules and make sure they are securely seated. Removing
any device should not result in the system not booting. You may also want to run diagnostics on the ram overnight with: http://www.memtest86.com/ http://www.memtest.org/ http://oca.microsoft.com/en/windiag.asp -- Brian A. Sesko { MS MVP_Shell/User } Conflicts start where information lacks. http://basconotw.mvps.org/ Suggested posting do's/don'ts: http://www.dts-l.org/goodpost.htm How to ask a question: http://support.microsoft.com/kb/555375 "bobk" wrote in message news I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I never see any information. I have researched these beep codes and read posts describing securing the video card cables/connections, but I have a chipset that I did actually assure is snug to the motherboard. This generated no change. Does anyone have an idea as to a next step? -- Bob K |
#7
|
|||
|
|||
Bios problem
"bobk" wrote in message news I have a HP Pavillion 612 running win 98 SE that in an attempt to remove a program interrupting the sound card, I believe I deleted the monitor driver. On startup I get one long followed by two short beeps. The hard drive and CD ROM spin, I get two more short beeps and the monitor shuts down. Therefore, I never see any information. I have researched these beep codes and read posts describing securing the video card cables/connections, but I have a chipset that I did actually assure is snug to the motherboard. This generated no change. Does anyone have an idea as to a next step? That beep code on an Award BIOS indicates a "display card or monitor connected error". Check your monitor connection to your PC. Go into the BIOS and see if you can find out where the you can select the video or monitor, probably in something like PCI Plug and Play section. What was the program you were removing and how did you go about it? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Windows 98 Boot up problem due to ndiswan.vxd missing file | Martin Healy | Setup & Installation | 2 | May 4th 05 11:34 PM |
Folder Named [C:\Program] Opens Automatically on Start | Ted Belben | General | 2 | September 16th 04 11:39 PM |
HELP !! Defrag hang, not machine does not boot at all !! | Ryan | General | 4 | August 31st 04 08:22 PM |
creating a password | jean | General | 1 | July 15th 04 03:50 AM |
Please help! Display settings !! | Mitzi | Monitors & Displays | 12 | July 11th 04 05:19 AM |