A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows 98 » Printing
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

setting printer margins, eliminate a printer error with Windows 98 SE



 
 
Thread Tools Display Modes
  #1  
Old September 17th 04, 06:28 AM
Milt
external usenet poster
 
Posts: n/a
Default setting printer margins, eliminate a printer error with Windows 98 SE

Hello, can someone please tell me:
a) how to set up the margins on my printer, HP DEskjet
722C, I can not find where I can change them.
b) many times the width of printed page is wider than
what the printer will copy. Is there a setting also that
will make page shrink in width size for whole page
printing.
c)how can I eliminate an ERROR notice which appears each
time the printer finishes printing and sometimes during
its printing operation. The stated notice: HPFVLS06
caused a general protection fault in module HPFVLS06.EXE
at 0002 : 00000 276. It further threatens to shut the
computer down, but over the last two months it never has.
Appreciate your help!
  #2  
Old September 17th 04, 08:54 AM
Mary Sauer
external usenet poster
 
Posts: n/a
Default

Don't know if this is a solution, but it does address your issue
IntelliPoint 4.0: "HPVLS60" or "HPFVLS06" Error Message or Printer Problem After You
Install IntelliPoint 4.0 Software
http://support.microsoft.com/default...;EN-US;Q318845

Your printer has margin limitations that is set by the manufacturer. According to HP
your margins are .25 left and right and .46 bottom. Some printers have a Zoom smart
setting that will shrink the contents to fit the media.

--
Mary Sauer MS MVP
http://office.microsoft.com/
http://www.msauer.mvps.org/
news://msnews.microsoft.com
"Milt" wrote in message
...
Hello, can someone please tell me:
a) how to set up the margins on my printer, HP DEskjet
722C, I can not find where I can change them.
b) many times the width of printed page is wider than
what the printer will copy. Is there a setting also that
will make page shrink in width size for whole page
printing.
c)how can I eliminate an ERROR notice which appears each
time the printer finishes printing and sometimes during
its printing operation. The stated notice: HPFVLS06
caused a general protection fault in module HPFVLS06.EXE
at 0002 : 00000 276. It further threatens to shut the
computer down, but over the last two months it never has.
Appreciate your help!



  #3  
Old September 17th 04, 11:50 AM
Richard G. Harper
external usenet poster
 
Posts: n/a
Default

a) This setting would be in your word processing program, most likely under
Page Setup or similar.

b) I have never seen a printer or driver that will do this.

c) Uninstall your printer drivers and reinstall the latest version from the
HP web site.

--
Richard G. Harper [MVP Win9x]
* PLEASE post all messages and replies in the newsgroups
* for the benefit of all. Private mail is usually not replied to.
* My website, such as it is ...
http://rgharper.mvps.org/
* HELP us help YOU ... http://www.dts-l.org/goodpost.htm


"Milt" wrote in message
...
Hello, can someone please tell me:
a) how to set up the margins on my printer, HP DEskjet
722C, I can not find where I can change them.
b) many times the width of printed page is wider than
what the printer will copy. Is there a setting also that
will make page shrink in width size for whole page
printing.
c)how can I eliminate an ERROR notice which appears each
time the printer finishes printing and sometimes during
its printing operation. The stated notice: HPFVLS06
caused a general protection fault in module HPFVLS06.EXE
at 0002 : 00000 276. It further threatens to shut the
computer down, but over the last two months it never has.
Appreciate your help!



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Windows 98 with preinstalled Windows NT Paul D.Smith Setup & Installation 2 July 22nd 04 01:14 AM
Unwanted password to open Windows 98 Jack Greenfield General 2 July 20th 04 05:35 PM
Microsoft Security Bulletin MS04-024 - Vulnerability in Windows Shell Could Allow Remote Code Execution (839645) Gary S. Terhune General 2 July 14th 04 05:06 AM
Microsoft Security Bulletin MS04-023--Please Note! Gary S. Terhune General 4 July 14th 04 04:39 AM
Major Problem Matty General 3 July 4th 04 05:02 PM


All times are GMT +1. The time now is 11:37 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 Win98banter.
The comments are property of their posters.