A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows ME » Setup & Installation
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

kmixer(01) during install



 
 
Thread Tools Display Modes
  #1  
Old July 8th 04, 12:49 PM
Elizabeth
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

I am having trouble reinstalling ME on a compaq
computer. First thing I did was Format c:. Then after a
couple tries at a regular install I defaulted to the
extract all .CAB files and run setup /c. Doing this
everything went fine until the last 13 minutes of the
install. During the driver setup portion there was one
error cmdninst caused an error in kernell32.dll. I
thought this was likely my ethernet card, I always have
to install that driver manually after install. But then
when install got to the system configuration it kept
erroring and writing errors to the log. Now I've got an
error message I cannot seem to pass (it keeps coming back
everytime I restart, haven't finished install yet) BSOD
says File Name: kmixer (01) +00009066 Error:
00:0028:FF180CE6. Any advice would be appreciated. Can
I somehow run the system configuration again outside the
setup routine?
  #2  
Old July 8th 04, 08:00 PM
Noel Paton
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

That looks like a sound driver problem from here (Kmixer is the kernel audio
mixer)

Questions
Why are you reinstalling?
How are you reinstalling? - clean or OTT? - from the HD, or the CD?
Did you remember to disable your AV, and the BIOS protection?

Try disabling your sound card/chip and rebooting - with any luck it'll
complete the install, and you can then worry about the drivers and card.

--
Noel Paton (MS-MVP 2002-2004, Win9x)

Nil Carborundum Illegitemi
http://www.btinternet.com/~winnoel/millsrpch.htm

Please read http://dts-l.org/goodpost.htm on how to post messages to NG's
or
http://www.microsoft.com/presspass/f.../Mar27pmvp.asp

"Elizabeth" wrote in message
...
I am having trouble reinstalling ME on a compaq
computer. First thing I did was Format c:. Then after a
couple tries at a regular install I defaulted to the
extract all .CAB files and run setup /c. Doing this
everything went fine until the last 13 minutes of the
install. During the driver setup portion there was one
error cmdninst caused an error in kernell32.dll. I
thought this was likely my ethernet card, I always have
to install that driver manually after install. But then
when install got to the system configuration it kept
erroring and writing errors to the log. Now I've got an
error message I cannot seem to pass (it keeps coming back
everytime I restart, haven't finished install yet) BSOD
says File Name: kmixer (01) +00009066 Error:
00:0028:FF180CE6. Any advice would be appreciated. Can
I somehow run the system configuration again outside the
setup routine?



  #3  
Old July 9th 04, 04:33 AM
Elizabeth
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

Reinstall reason = an auto pop-up program got in, and I believe there was a virus because the computer kept having xxx caused an error in unknown errors. I tried stinger (after running once it couldn't find the V def file), AVG, Ad-aware which all didn't do much. CWShredder was the next thing I was going to try but then the registry kept having errors even after running scanreg /fix. Thus I gave up trying to fix it, data was already backed up, nothing lost.

Reinstall method = clean HD(via running format c: ). But had errors so ended up copying & extracting files (from ME install disk to c:\w9xflat) so ran setup from HD, not CD.
At this point I don't have it connected to internet until I get my basic programs (windows, AV, firewall) installed. So right now there is no AV, and I have no BIOS protection enabled.

Would you give me some direction on how to disable the sound card/chip? I'm sure the steps are basic but I cannot figure it out in DOS. When looking in my BIOS I see that both the Ethernet Controller and Compaq Audio Device are both on IRQ5. And if I change the IRQ for one, they both change. I removed the audio references that I saw in system.ini (after creating a backup of course). When the computer is restarted (w/o EBD) Windows ME starts with the flash screen, goes black, then gives me the KMixer error again. If I press any key after the error I get a blue blank screen, after a Ctrl+atl+del I see that the only task listed is mmtask. I just have the manufacturer installed sound, speakers aren't plugged in (figured I could add accessories one at a time later).

Thanks for your help!

  #4  
Old July 9th 04, 04:36 AM
Elizabeth
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

Reinstall reason = an auto pop-up program got in, and I believe there was a virus because the computer kept having xxx caused an error in unknown errors. I tried stinger (after running once it couldn't find the V def file), AVG, Ad-aware which all didn't do much. CWShredder was the next thing I was going to try but then the registry kept having errors even after running scanreg /fix. Thus I gave up trying to fix it, data was already backed up, nothing lost.

Reinstall method = clean HD(via running format c: ). But had errors so ended up copying & extracting files (from ME install disk to c:\w9xflat) so ran setup from HD, not CD.
At this point I don't have it connected to internet until I get my basic programs (windows, AV, firewall) installed. So right now there is no AV, and I have no BIOS protection enabled.

Would you give me some direction on how to disable the sound card/chip? I'm sure the steps are basic but I cannot figure it out in DOS. When looking in my BIOS I see that both the Ethernet Controller and Compaq Audio Device are both on IRQ5. And if I change the IRQ for one, they both change. I removed the audio references that I saw in system.ini (after creating a backup of course). When the computer is restarted (w/o EBD) Windows ME starts with the flash screen, goes black, then gives me the KMixer error again. If I press any key after the error I get a blue blank screen, after a Ctrl+atl+del I see that the only task listed is mmtask. I just have the manufacturer installed sound, speakers aren't plugged in (figured I could add accessories one at a time later).

Thanks for your help! (my first response errored, so I hope I'm not double posting)

  #5  
Old July 9th 04, 06:35 AM
Noel Paton
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

Go into the BIOS and switch off both the Ethernet controller, and the Sound
there, then reformat again, and reinstall.
I suspect that Compaq have, in their usual way, used highly proprietary
hardware, which a 'normal' ME can't cope with. (Is the ME you're using an
OEM disk, or an MS one?)


--
Noel Paton (MS-MVP 2002-2004, Win9x)

Nil Carborundum Illegitemi
http://www.btinternet.com/~winnoel/millsrpch.htm

Please read http://dts-l.org/goodpost.htm on how to post messages to NG's
or
http://www.microsoft.com/presspass/f.../Mar27pmvp.asp

"Elizabeth" wrote in message
...
Reinstall reason = an auto pop-up program got in, and I believe there was

a virus because the computer kept having xxx caused an error in unknown
errors. I tried stinger (after running once it couldn't find the V def
file), AVG, Ad-aware which all didn't do much. CWShredder was the next
thing I was going to try but then the registry kept having errors even after
running scanreg /fix. Thus I gave up trying to fix it, data was already
backed up, nothing lost.

Reinstall method = clean HD(via running format c: ). But had errors so

ended up copying & extracting files (from ME install disk to c:\w9xflat) so
ran setup from HD, not CD.
At this point I don't have it connected to internet until I get my basic

programs (windows, AV, firewall) installed. So right now there is no AV,
and I have no BIOS protection enabled.

Would you give me some direction on how to disable the sound card/chip?

I'm sure the steps are basic but I cannot figure it out in DOS. When
looking in my BIOS I see that both the Ethernet Controller and Compaq Audio
Device are both on IRQ5. And if I change the IRQ for one, they both change.
I removed the audio references that I saw in system.ini (after creating a
backup of course). When the computer is restarted (w/o EBD) Windows ME
starts with the flash screen, goes black, then gives me the KMixer error
again. If I press any key after the error I get a blue blank screen, after a
Ctrl+atl+del I see that the only task listed is mmtask. I just have the
manufacturer installed sound, speakers aren't plugged in (figured I could
add accessories one at a time later).

Thanks for your help!



  #6  
Old July 16th 04, 03:32 AM
Elizabeth
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

That fixed it, thanks! I was using a MS ME disk. I
think you 100% correct with Compaq and ME. I also
minimized my ME install and added features a couple at
time.
-----Original Message-----
Go into the BIOS and switch off both the Ethernet

controller, and the Sound
there, then reformat again, and reinstall.
I suspect that Compaq have, in their usual way, used

highly proprietary
hardware, which a 'normal' ME can't cope with. (Is the

ME you're using an
OEM disk, or an MS one?)


--
Noel Paton (MS-MVP 2002-2004, Win9x)


  #7  
Old July 16th 04, 05:07 AM
Noel Paton
external usenet poster
 
Posts: n/a
Default kmixer(01) during install

Great - well done!
Thanks for the feedback.

--
Noel Paton (MS-MVP 2002-2004, Win9x)

Nil Carborundum Illegitemi
http://www.btinternet.com/~winnoel/millsrpch.htm
http://tinyurl.com/6oztj

Please read http://dts-l.org/goodpost.htm on how to post messages to NG's

"Elizabeth" wrote in message
...
That fixed it, thanks! I was using a MS ME disk. I
think you 100% correct with Compaq and ME. I also
minimized my ME install and added features a couple at
time.
-----Original Message-----
Go into the BIOS and switch off both the Ethernet

controller, and the Sound
there, then reformat again, and reinstall.
I suspect that Compaq have, in their usual way, used

highly proprietary
hardware, which a 'normal' ME can't cope with. (Is the

ME you're using an
OEM disk, or an MS one?)


--
Noel Paton (MS-MVP 2002-2004, Win9x)




 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
floppy challenge, trying to ready a machine for win98se install niteowl Setup & Installation 7 July 19th 04 10:08 PM
Reformat Windows Ron General 2 July 10th 04 08:26 PM
Clean Install of Windows without disc JS Setup & Installation 5 June 28th 04 08:14 PM
Install Win98SE over W95b or erase W95b?...and more! Bob G Setup & Installation 2 June 25th 04 09:55 PM
Clean Install of Windows 98 DL Disk Drives 1 June 9th 04 11:40 PM


All times are GMT +1. The time now is 09:07 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 Win98banter.
The comments are property of their posters.