If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Scandisk/Defrag
When I attempt to do a Defrag on secondary drive D:\ (not C:\) I get a
message saying that I need to execute Scandisk first, which I do. However, when Scandisk gets to about 2/3 of the way it stops and if I start it again, it stops at the same place. How do I get to complete Scandisk and\or fix the inherent problem. Thanking you in anticipation PS I use Window ME |
#2
|
|||
|
|||
You *may* be seeing the early signs of a failing hard drive. Try running
Scandisk in Real Mode DOS. Boot using your WinMe Startup (floppy) Disk and at the A:\ prompt, type: scandisk d: (Note the syntax - space between k and d followed by a colon) Then press return. If it shows errors, do not let it 'fix' them or do a Surface Test until you have backed up your data - you may need professional assistance if you're not sure how to copy or recover your data files. However, if you are prepared to lose data, then let it repair errors and do the surface scan. Hopefully - and with a bit of luck g - it may even fix the problem. Good luck Mart "emmesse" wrote in message ... When I attempt to do a Defrag on secondary drive D:\ (not C:\) I get a message saying that I need to execute Scandisk first, which I do. However, when Scandisk gets to about 2/3 of the way it stops and if I start it again, it stops at the same place. How do I get to complete Scandisk and\or fix the inherent problem. Thanking you in anticipation PS I use Window ME |
#3
|
|||
|
|||
Boot into Safe Mode and run from there.
"emmesse" wrote in message ... When I attempt to do a Defrag on secondary drive D:\ (not C:\) I get a message saying that I need to execute Scandisk first, which I do. However, when Scandisk gets to about 2/3 of the way it stops and if I start it again, it stops at the same place. How do I get to complete Scandisk and\or fix the inherent problem. Thanking you in anticipation PS I use Window ME |
#4
|
|||
|
|||
Thank you Mart, It wooooorked!! Much obliged.
Emmesse "Mart" wrote: You *may* be seeing the early signs of a failing hard drive. Try running Scandisk in Real Mode DOS. Boot using your WinMe Startup (floppy) Disk and at the A:\ prompt, type: scandisk d: (Note the syntax - space between k and d followed by a colon) Then press return. If it shows errors, do not let it 'fix' them or do a Surface Test until you have backed up your data - you may need professional assistance if you're not sure how to copy or recover your data files. However, if you are prepared to lose data, then let it repair errors and do the surface scan. Hopefully - and with a bit of luck g - it may even fix the problem. Good luck Mart "emmesse" wrote in message ... When I attempt to do a Defrag on secondary drive D:\ (not C:\) I get a message saying that I need to execute Scandisk first, which I do. However, when Scandisk gets to about 2/3 of the way it stops and if I start it again, it stops at the same place. How do I get to complete Scandisk and\or fix the inherent problem. Thanking you in anticipation PS I use Window ME |
#5
|
|||
|
|||
You're welcome Emmesse - and thanks for the feedback and I therefore trust
that your drive has recovered successfully without any failure or loss of data. Mart "Emmesse" wrote in message ... Thank you Mart, It wooooorked!! Much obliged. Emmesse "Mart" wrote: You *may* be seeing the early signs of a failing hard drive. Try running Scandisk in Real Mode DOS. Boot using your WinMe Startup (floppy) Disk and at the A:\ prompt, type: scandisk d: (Note the syntax - space between k and d followed by a colon) Then press return. If it shows errors, do not let it 'fix' them or do a Surface Test until you have backed up your data - you may need professional assistance if you're not sure how to copy or recover your data files. However, if you are prepared to lose data, then let it repair errors and do the surface scan. Hopefully - and with a bit of luck g - it may even fix the problem. Good luck Mart "emmesse" wrote in message ... When I attempt to do a Defrag on secondary drive D:\ (not C:\) I get a message saying that I need to execute Scandisk first, which I do. However, when Scandisk gets to about 2/3 of the way it stops and if I start it again, it stops at the same place. How do I get to complete Scandisk and\or fix the inherent problem. Thanking you in anticipation PS I use Window ME |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
scandisk/defrag | Richard | General | 2 | August 24th 04 10:03 PM |
scandisk/defrag | Joyce Marshall | Improving Performance | 7 | July 4th 04 01:55 PM |