If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Hello Mart,
This problem only started Sunday 02/01/05 had no problems untill then. As for anyone poking under the bonnet, (Inside the Machine) I myself am the only person using the computer,Switch it on and run programes is my "TEC" skills. It all seemed to happen after Un-Installing and Re-Installing that Dammed Norton and it's files. As for the clock settings,yes they are set to,"GMT,Dublin,London,ect, ect,always have been,and clock is set to correct time. Seamey. "Mart" wrote: My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#12
|
|||
|
|||
Mart - unless you've actually had an email from Seamey, he's using the CDP -
so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock) I have no idea why one of his posts appears to have a back-timed stamp! -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#13
|
|||
|
|||
It all seemed to happen after Un-Installing and Re-Installing
that Dammed Norton and it's files. Mmm.. Not relevant to the CD-ROM issue, as booting from the floppy into DOS does not bring anything on the HDD (especially Norton!!) into action. So it would appear that your CD-ROM has died after all - Coincidence?? - Just bad luck, I guess :-( So it's off to PC World then g As for the clock settings, yes they are set to,"GMT, Dublin, London, etc, etc, always have been, and clock is set to correct time. What time-stamp is shown in the Propertis/Details on your PC for your (and my) received mail? Your last one at 17.25 is being shown as 09.25. Is your clock set for am or pm?? Nah... it's 8 hrs not 12 hrs wrong. Perhaps the 8hr discrepancy has something to do with posting via MS CDO rather than using Outlook Express - maybe someone else can explain. **Just seen your post before pressing the Send button, Noel g - Thanks!!** Typically, what sort of files & folders are "greyed out"? (In Windows Explorer?) Right-click on one (or few) and select Properties. Are they 'System' files/folders? What are their attributes shown as (compared to those NOT greyed-out)? Mart "Seamey.T" wrote in message ... Hello Mart, This problem only started Sunday 02/01/05 had no problems untill then. As for anyone poking under the bonnet, (Inside the Machine) I myself am the only person using the computer,Switch it on and run programes is my "TEC" skills. It all seemed to happen after Un-Installing and Re-Installing that Dammed Norton and it's files. As for the clock settings,yes they are set to,"GMT,Dublin,London,ect, ect,always have been,and clock is set to correct time. Seamey. "Mart" wrote: My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#14
|
|||
|
|||
**Just seen your post before pressing the Send button, Noel g - Thanks!!**
I have no idea why one of his posts appears to have a back-timed stamp! They are ALL 8Hrs out - at least in this thread, Noel g Mart "Noel Paton" wrote in message ... Mart - unless you've actually had an email from Seamey, he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock) I have no idea why one of his posts appears to have a back-timed stamp! -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#15
|
|||
|
|||
Hmmm - I have timestamps.....
07:37 - S 15:14 - M next day 13:15 - S 16:47 - M 21:15 - S 23:33 - M next day 02:03 - S 08:58 - M 15:11 - S 16:10 - M 17:25 - S 18:13 - M ( and that even removes the odd one that I though was there!) All in logical order, no branching or whatever....... -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... **Just seen your post before pressing the Send button, Noel g - Thanks!!** I have no idea why one of his posts appears to have a back-timed stamp! They are ALL 8Hrs out - at least in this thread, Noel g Mart "Noel Paton" wrote in message ... Mart - unless you've actually had an email from Seamey, he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock) I have no idea why one of his posts appears to have a back-timed stamp! -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#16
|
|||
|
|||
Which is what I am seeing as well, nothing as far as I can see out of
order. :-) -- Mike Noel Paton wrote: Hmmm - I have timestamps..... 07:37 - S 15:14 - M next day 13:15 - S 16:47 - M 21:15 - S 23:33 - M next day 02:03 - S 08:58 - M 15:11 - S 16:10 - M 17:25 - S 18:13 - M ( and that even removes the odd one that I though was there!) All in logical order, no branching or whatever....... |
#17
|
|||
|
|||
That's what I'm seeing although mine are in am /pm mode g
Joan "Noel Paton" wrote in message ... Hmmm - I have timestamps..... 07:37 - S 15:14 - M next day 13:15 - S 16:47 - M 21:15 - S 23:33 - M next day 02:03 - S 08:58 - M 15:11 - S 16:10 - M 17:25 - S 18:13 - M ( and that even removes the odd one that I though was there!) All in logical order, no branching or whatever....... -- Noel Paton (MS-MVP 2002-2005, Windows) |
#18
|
|||
|
|||
I should have said - "Take a look at the 'Properties' \ 'Details' -
they (Seamey's) are all -0800" mine are all -0000 Like you said Noel, "he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock)" Never noticed that affect before - always ASSumed it to be correct bg Mart "Noel Paton" wrote in message ... Hmmm - I have timestamps..... 07:37 - S 15:14 - M next day 13:15 - S 16:47 - M 21:15 - S 23:33 - M next day 02:03 - S 08:58 - M 15:11 - S 16:10 - M 17:25 - S 18:13 - M ( and that even removes the odd one that I though was there!) All in logical order, no branching or whatever....... -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... **Just seen your post before pressing the Send button, Noel g - Thanks!!** I have no idea why one of his posts appears to have a back-timed stamp! They are ALL 8Hrs out - at least in this thread, Noel g Mart "Noel Paton" wrote in message ... Mart - unless you've actually had an email from Seamey, he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock) I have no idea why one of his posts appears to have a back-timed stamp! -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#19
|
|||
|
|||
mine are all -0000
And so are yours, Mikes and Joans! But not Seamey's Mart "Mart" wrote in message ... I should have said - "Take a look at the 'Properties' \ 'Details' - they (Seamey's) are all -0800" mine are all -0000 Like you said Noel, "he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock)" Never noticed that affect before - always ASSumed it to be correct bg Mart "Noel Paton" wrote in message ... Hmmm - I have timestamps..... 07:37 - S 15:14 - M next day 13:15 - S 16:47 - M 21:15 - S 23:33 - M next day 02:03 - S 08:58 - M 15:11 - S 16:10 - M 17:25 - S 18:13 - M ( and that even removes the odd one that I though was there!) All in logical order, no branching or whatever....... -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... **Just seen your post before pressing the Send button, Noel g - Thanks!!** I have no idea why one of his posts appears to have a back-timed stamp! They are ALL 8Hrs out - at least in this thread, Noel g Mart "Noel Paton" wrote in message ... Mart - unless you've actually had an email from Seamey, he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock) I have no idea why one of his posts appears to have a back-timed stamp! -- Noel Paton (MS-MVP 2002-2005, Windows) Nil Carborundum Illegitemi http://www.btinternet.com/~winnoel/millsrpch.htm http://tinyurl.com/6oztj Please read http://dts-l.org/goodpost.htm on how to post messages to NG's "Mart" wrote in message ... My clock is set to "GMT" is that correct? Yes... but! .. is your Time Zone correctly set to GMT : Dublin, London, etc., in Control Panel | Date & Time \Time Zone? You're showing 8 Hrs behind in your e-mail properties. However, you have now put a whole new complexion on the issue!! You didn't mention the DVD-RW before!!! So let's just step backwards a little. When booting from the floppy Startup Disk, you *should* have seen TWO CD-ROMS, becoming the E: and the F:, so the screen *should* have shown: Drive E:= Driver MSCD001 UNIT 0 Drive F:= Driver MSCD001 UNIT 1 Your CD-ROM Is Drive E In other words, ONE of your CD-ROM drives was missing!!! (NB. although it is a DVD, DOS only recognises it as a CD-ROM) (Don't worry that you didn't also see a further line "Your CD-ROM Is Drive F" - you won't.) And!! had (it) fitted 6months ago. When did your CD-ROM go AWOL?? Coincidence?? Back to my original question - Have you (or anybody else!!) been poking about under the bonnet and knocked/dislodged any connectors? My revised guess is that a visit back to whoever fitted your DVD *might* be a better proposition, before you throw cash at a possibly unnecessary new CD-ROM. I'll cover your other problem later - first sort this one out g Mart "Seamey.T" wrote in message ... Hi Mart, yeah your side of the water,well almost,N.Ireland (Belfast) My clock is set to "GMT" is that correct? Thanks for the advice on the CD-ROM will buy one tomorrow,as for the CD-RW, had a new DVD-RW (Pioneer 107D) fitted 6months ago. Thank you so very much for all your help and bearing with me,and if you do come up with any suggestion regarding those' Faded Files',can you mail me, Keep up the execellent work and may the New Year be kind to you and all in the Forum, Seamey.T "Mart" wrote: Hi Seamey, - from my side of the water? The UK? Then your clock is 8 hrs behind GMT (UK time) g The fact that you cant get it to work in (Real Mode) DOS (via the Startup floppy Disk) means that WinMe (and your hard drive) are completely eliminated from the equation. - Although your deletions of the Norton files etc. *may* raise their head later - hence one thing at a time g. I wouldn't really recommend any specific make of CD-ROM as I think most are made by only a couple of manufacturers and just re-badged. Mine are LG but don't take that as an endorsement. Try your local PC store (PC World?) and see what they have to offer. You may wish to think of replacing it with a burner (CD-RW) but you will need suitable software. In the meantime, I'll have a think about the 'faded folders' Mart "Seamey.T" wrote in message ... "Mart" wrote: Ah... So it probably didn't even open in WinMe? (Not even using the button on the front panel?) In which case, back to my earlier comments - Have you been poking about under the bonnet and knocked/dislodged any connectors? If not, You (may) *almost certainly* have a faulty CD-ROM ...! Substitution/replacement is the only practical solution. I would guess that a new one should only be about US$25 or so - they're less than GBP10 over here. Good luck with it. Mart "Seamey.T" wrote in message ... Hi Mart, Sorry for the hassle but just reading over your instructions and can't do anything with the CD-ROM,the tray will not open to let me put a Cd in,baffled. "Mart" wrote: Things initially look OK there. Firstly, the CD-ROM is being recognised in DOS and is being assigned a letter (E). After things have settled down, then at the A:\ prompt, you need to type:- E: (then press Return) that should then give you an E:\ prompt. Now put a (data) CD into your CD-COM and type:- dir (then press return) [or dir /p to stop the screen from scrolling] and you should see a listing of the contents of the CD. If all is well, then you need to worry about why WinMe is not recognising it - come back and let us know how you get on so far and someone should be able to continue with help. BTW - To get out of Real Mode DOS, you can either Power-off your PC (as you have now discovered g) or, remove the floppy disk and press Ctrl+Alt+Del. You can't directly get back into WinMe!! ....I just hope I haven't done any damage. No, you won't have damaged anything - at least as far as this is concerned. .... have I deleted something I should'nt have. Not sure yet - see how you get on with the first part. Mart "Seamey.T" wrote in message ... "Mart" wrote: One thing at a time! ... my CD-ROM is not working. Went to Device Manager and doesn't show there. Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing, NB. You won't see your CD-ROM in DevMan in Safe Mode, the drivers are only loaded in Normal Mode. However, if your not seeing it in Normal Mode, then boot using your WinMe (floppy) Startup Disk and select 'With CD-ROM support' and see if it is recognised in DOS. (It *should* report a drive letter for your CD-ROM which is not necessarily the same letter as you would expect in Windows). If the CD-ROM is not being recognised in DOS, you will have to boot into your BIOS to confirm that it is recognised there. Have you been poking about under the bonnet and knocked/dislodged any connectors? You *may* have a faulty CD-ROM of course! Mart "Seamey.T" wrote in message ... Hi Guys, Have just noticed that a lot of my Files and Folders are Greyed out and am begining to panic.I went into Windows/temp and deleted a lot of stuff which I thought were safe to remove, but now I've just discoverd my CD-ROM is not working. Went to Device Manager and doesn't show there.Rebooted into safe mode to see if it would re-appear when I booted up in Normal but nothing,what the heck have Idone. Hi Mart, Well did as you instructed and yes it was recognized in "DOS" but I had to restart my computer to get out of it. This is the read out it gave me, "The Diagnostil Tools Were Succesfully loaded To Drive (D)"MSCDEX VERSION 2.25 Copyright (c) Microsoft Corp.1986-1995 "Drive E:=DriverMSCD001 UNIT 0 Your CD-ROM Is Drive E" The "DOS" Screen then showed this,"COR101:Not Ready Reading Drive E Abort,Retry,Fail, I let this run thinking it normal,but 18hrs later,surely not,it would not let me Exit,I just hope I haven't done any damage. This all came about while i was Un-Installing and Re-Installing an Anti-Virus program were i had to go into Files and Folders to delete Shared and Temp Files,have I deleted something I should'nt have. Hi Mart, I wouldn't have a clue how to get under the bed never mind this machine. You're right I can't open the CD-ROM from the button at the front of the CPU and the Orange light is on permanent were it's normally off or flashing . I deleted some files last week and this happened, so I quickly restored them back and the CD-ROM worked again,weather this was a factor or not.Was just wondering when I was deleting those Norton Files and Temp's did I make a ricky somewhere.Checking through "MS,Troubleshooting" all day,and these Forums but only found one thing,probably has nothing to do with my problem. "MS" Artical ID:275499 (Troubleshooting Device Driver Issues Using The Driver Information Database) "Mart" please don't think I'm trying to under-mind your efforts,not by a long way,us "Dummies" couldn't survive in this "Tec"world without you folks. If it is a new CD-ROM I need, could you recommend a good one,I'm from your side of the water and price is no-matter. Could you look into the other matter I asked about,the faded out Files&Folders, Thank You. |
#20
|
|||
|
|||
Mart,
AFAIK the CDO clock is correct, that is once your news client applies he -8.00 hours correction. What you are seeing is one of the many reasons why the CDO web interface causes so many problems to those trying to help others in the newsgroups. Namely it hides not only the posters IP address but also by making all posts as if made from Redmond obscures the real location of the user. Add to that a failure to provide any details of the operating system or version in use, such as provided in many cases by the X-Newsreader and X-MimeOLE headers in NNTP posts, taken together it makes helping CDO posters a bit akin to working with a bag over your head. :-) A bit extreme perhaps but IP address can help with ISP problems, Path with news server problems, time zone with localisation problems (such as keyboard) and as for Mailer/MIME versions I need to make no comment. Cheers, -- Mike Mart wrote: I should have said - "Take a look at the 'Properties' \ 'Details' - they (Seamey's) are all -0800" mine are all -0000 Like you said Noel, "he's using the CDP - so has no control of the posting time (which is not affected by local settings, except for the Redmond server clock)" Never noticed that affect before - always ASSumed it to be correct bg |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Win9x : Utility to dynamic mapping TEMP to memory ? | Libor Striz | General | 22 | September 15th 04 06:56 AM |
Find: files and folders - clear search history | Randy | General | 2 | July 27th 04 06:20 AM |
C Windows profiles user application data | LuckyStrike | General | 24 | June 18th 04 12:13 AM |
Question about C:\Windows\Temp files | JR Berry | General | 6 | June 7th 04 09:32 PM |
Windows Me Start/Search For Files or Folders Doesn't Work | Greg | Software & Applications | 0 | May 6th 04 02:03 PM |