If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Screen size/font
I have similar problems with the screen being enlarged to
the point I can not work normally. I have followed other suggestions to go to the COntrol Panel, select Display, then select Setting and move the screen area slider to the right or in the direction of the More. This can be done, but I must select either OK or Apply and those buttons are either hidden or not highlighted. Any suggestions ? |
#2
|
|||
|
|||
Screen size/font
Reinstall the video display adapter driver. Here's my standard blurb in
case you need help: When the correct screen resolution (screen area) or the right number of colors are not available choices in display properties, settings tab, then it is a good bet you do not have the right driver installed for your display adapter. The display adapter in your PC is either a video card or a display chipset on the motherboard. If you received a CD or floppy disks with drivers along with your PC, see if they contain a display adapter driver and install it using: control panel, system, device manager, display adapter. If you know what display adapter your PC has but you have no disks, use www.google.com to track down the correct driver on the internet. If you do not know what display adapter your PC uses, you can go to a MS-DOS prompt and type: Debug and hit enter. The screen will display a flashing prompt next to a - sign. Type: DC000:35 (DC000:50 may also work) and hit enter. The name and possibly model of your display adapter should appear on the right hand side of the screen. To quit Debug, type Q and hit enter. If Debug is not helpful, you can try this program: Advanced PCI Info, available at: http://www.upsystems.com.ua/support/alexmina/ If all else fails, you will have to remove the computer case. Look at where the monitor plugs into the back of the case and then check that location inside the case. If there is a card there, you obviously have a video card and if not, you have on board graphics. Write down any information displayed on either the card or the chipset on the motherboard. Then use www.google.com to search for the information. Do not include all the data you found in one search message--search on each piece individually. If you include all the information at once, you might not get a hit. I have found that a video card will generally have to be removed in order to see the information. Be careful of static electricity as it can fry components. Before touching anything in the computer case (the cord is unplugged, right?), ground yourself to the case by touching it. Don't work on carpeting since shuffling your feet on it can generate static electricity after you grounded yourself. Remove the one screw that holds the card in place and using a rocking motion (left to right and back) and pull the card straight out. Once you have the right driver, install it through control panel, system, device manager or through control panel, add new hardware, as appropriate. -- Regards Ron Badour, MS MVP for W98 Tips: http://home.satx.rr.com/badour Knowledge Base Info: http://support.microsoft.com/default.aspx?pr=kbinfo " wrote in message ... I have similar problems with the screen being enlarged to the point I can not work normally. I have followed other suggestions to go to the COntrol Panel, select Display, then select Setting and move the screen area slider to the right or in the direction of the More. This can be done, but I must select either OK or Apply and those buttons are either hidden or not highlighted. Any suggestions ? |
#3
|
|||
|
|||
Screen size/font
Just press Enter after making the change to screen area. That's the same as
pressing OK or Apply. -- Jeff Richards MS MVP (DTS) " wrote in message ... I have similar problems with the screen being enlarged to the point I can not work normally. I have followed other suggestions to go to the COntrol Panel, select Display, then select Setting and move the screen area slider to the right or in the direction of the More. This can be done, but I must select either OK or Apply and those buttons are either hidden or not highlighted. Any suggestions ? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Preventing a Screen Capture? | Bill | General | 1 | August 1st 04 01:36 PM |
Screen size | Trinidad Latvel | Improving Performance | 2 | July 12th 04 09:43 PM |
black screen at windows start | Coyote | General | 2 | July 7th 04 12:25 PM |
Splash and ME startup screen has changed size | Julia | Monitors & Displays | 0 | June 29th 04 01:13 PM |
Start Screen or Shut Down Screen | mo? | General | 0 | June 25th 04 03:38 AM |