If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
PS- Tim, if you decide that the mobo battery needs changing, be sure to
go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. -- Gary S. Terhune MS MVP Shell/User http://www.grystmill.com/articles/cleanboot.htm http://www.grystmill.com/articles/security.htm "Gary S. Terhune" wrote in message ... The motherboard battery is typically a disk-type such as you find in watches, though much larger than a watch battery. About /8 to 1 inch in diameter. It's in a clip mounting, relatively easy to swap--*if* the case is arranged to make it easy to get to. You won't know what model battery until you remove the old one unless your motherboard documentation includes the info. As Dan notes, malware (viruses, spyware, adware) sometimes has this effect, also, though it is certainly not limited to such. It can eve be a simple procedure like moving a ton of files that will cause the slowdown. However, since yours is a chronic affair, I'd suspect malware or a background app or an app that you use heavily. For suggestions on malware removal and protection, and hints on how to create a Clean Boot environment suitable for starting a trouble-shooting procedure, see the articles in my signature. -- Gary S. Terhune MS MVP Shell/User http://www.grystmill.com/articles/cleanboot.htm http://www.grystmill.com/articles/security.htm "Tim" wrote in message ... Thanks for these pointers--I just reset the time so I'll have to wait to check if the clock resets upon restart. But if the motherboard battery is going dead, what do I do for that! I've never even heard of a motherboard battery. What does it do? Thanks again, Tim "Gary S. Terhune" wrote: Does it reset to correct time when you restart? If not, your motherboard battery is going dead. If the clock resets to correct time when you restart, it's a known problem caused by any number of programs. The technical explanation is a bit involved, but the only solutions are to 1. Determine which program(s) cause the problem and get along without them, or 2. Get an app that regularly checks an online atomic click and synchronizes your clock. There are many such apps out there. I don't have any recommendations. -- Gary S. Terhune MS MVP Shell/User http://www.grystmill.com/articles/cleanboot.htm http://www.grystmill.com/articles/security.htm "Tim" wrote in message ... Does anybody know why my Windows clock doesn't keep correct time. It seems to fall behind the right time. Thanks, Tim |
#12
|
|||
|
|||
Gary S. Terhune wrote:
When I posted my previous response here, I had just started a Copy operation of some 16 GB on a WIn98SE system (fresh install.) Copying my wife's entire WinXP system to another drive. (Old drive went bad.) It's been running about an hour and a half--and has lost 20 minutes on the clock. Don't know about now but in "the old days" interrupts had to be disabled before all disk (floppy) read/writes and a DI meant the clock lost time. -- dadiOH ____________________________ dadiOH's dandies v3.06... ....a help file of info about MP3s, recording from LP/cassette and tips & tricks on this and that. Get it at http://mysite.verizon.net/xico |
#13
|
|||
|
|||
"dadiOH" wrote in message
... Gary S. Terhune wrote: When I posted my previous response here, I had just started a Copy operation of some 16 GB on a WIn98SE system (fresh install.) Copying my wife's entire WinXP system to another drive. (Old drive went bad.) It's been running about an hour and a half--and has lost 20 minutes on the clock. Don't know about now but in "the old days" interrupts had to be disabled before all disk (floppy) read/writes and a DI meant the clock lost time. Yup, and that's also the case for many other low-level operations. -- Gary S. Terhune MS MVP Shell/User http://www.grystmill.com/articles/cleanboot.htm http://www.grystmill.com/articles/security.htm |
#14
|
|||
|
|||
http://support.microsoft.com/default...12&Product=w98
Restart or Network Connection Changes Computer Date and Time To determine whether it is something in Windows or something pre-Windows (battery/BIOS setting)... (1) Set clock in Windows. Shut down overnight (or long enough). (2) Boot to Command Prompt Only, by holding CTRL as you boot to get the Startup Menu, if it isn't already enabled at "START, Run, MSConfig, Advanced button". (3) Enter "TIME", no quotes. (Then, ENTER, to exit w/o changing.) (4) Ctrl-Alt-Del to boot Windows. Was the time wrong in DOS?.. It's the battery or BIOS, then. Otherwise, it is something about Windows, maybe the Startup Group or a driver. C:\time/? Displays or sets the system time. TIME [time] Type TIME with no parameters to display the current time setting and a prompt for a new one. Press ENTER to keep the same time. C:\time Current time is 6:54:27.68p Enter new time: -- Thanks or Good Luck, There may be humor in this post, and, Naturally, you will not sue, should things get worse after this, PCR "Tim" wrote in message ... | Does anybody know why my Windows clock doesn't keep correct time. It seems to | fall behind the right time. Thanks, Tim |
#15
|
|||
|
|||
Gary S. Terhune wrote:
PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" |
#16
|
|||
|
|||
There are such utilities, yes. But you have to get past BIOS to load a
floppy. While there's not likely to be any problem doing that, I prefer going straight into BIOS and configuring before *anything* else. -- Gary S. Terhune MS MVP Shell/User http://www.grystmill.com/articles/cleanboot.htm http://www.grystmill.com/articles/security.htm "Chuck" wrote in message ... Gary S. Terhune wrote: PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" |
#17
|
|||
|
|||
"Chuck" wrote in message ... Gary S. Terhune wrote: PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" Yes. There are programs available to do that. I know I have one lying around somewhere, perhaps on one of my Resource Kits. I've never had a need for it. I just use autodetect, or punch in the drive parameters stamped on the label. |
#18
|
|||
|
|||
Hugh Candlin wrote:
"Chuck" wrote in message ... Gary S. Terhune wrote: PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" Yes. There are programs available to do that. I know I have one lying around somewhere, perhaps on one of my Resource Kits. I've never had a need for it. I just use autodetect, or punch in the drive parameters stamped on the label. I've never written down any of my bios settings. Does the "print screen" button work while in the bios. If so maybe I'll just go to the critical sections and print them out. -- To reply by email remove "_nospam" |
#19
|
|||
|
|||
On Thu, 17 Feb 2005 14:17:03 -0500, Chuck
wrote: Hugh Candlin wrote: "Chuck" wrote in message ... Gary S. Terhune wrote: PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" Yes. There are programs available to do that. I know I have one lying around somewhere, perhaps on one of my Resource Kits. I've never had a need for it. I just use autodetect, or punch in the drive parameters stamped on the label. I've never written down any of my bios settings. Does the "print screen" button work while in the bios. If so maybe I'll just go to the critical sections and print them out. Chuck, Get Cmossave/cmosrest.zip. It's a small utility. The program will record the CMOS settings into a file and restore them whenever needed. Read the text file. Put a copy of the CMOS saved file on the HDD and a floppy. http://www.majorgeeks.com/download4049.html I have version 1.4 but haven't used it. Regards, Bill Watt Computer Help and Information http://home.epix.net/~bwatt/ |
#20
|
|||
|
|||
On Thu, 17 Feb 2005 22:49:26 -0500, Bill Watt
wrote: On Thu, 17 Feb 2005 14:17:03 -0500, Chuck wrote: Hugh Candlin wrote: "Chuck" wrote in message ... Gary S. Terhune wrote: PS- Tim, if you decide that the mobo battery needs changing, be sure to go into BIOS *before* changing it and write down all the settings there. You'll have to reset them after replacing the battery. Isn't there a way to save the BIOS settings to a floppy (you probably couldn't access the HD after yanking the battery). -- To reply by email remove "_nospam" Yes. There are programs available to do that. I know I have one lying around somewhere, perhaps on one of my Resource Kits. I've never had a need for it. I just use autodetect, or punch in the drive parameters stamped on the label. I've never written down any of my bios settings. Does the "print screen" button work while in the bios. If so maybe I'll just go to the critical sections and print them out. Chuck, Get Cmossave/cmosrest.zip. It's a small utility. The program will record the CMOS settings into a file and restore them whenever needed. Read the text file. Put a copy of the CMOS saved file on the HDD and a floppy. http://www.majorgeeks.com/download4049.html I have version 1.4 but haven't used it. I just got ver 3.8. The Ga download site didn't work but the Fla. one did. It's only 29k. Don't keep old saves around so you don't accidentally restore an old one. Regards, Bill Watt Computer Help and Information http://home.epix.net/~bwatt/ |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Registery problem? | Paul | General | 15 | December 8th 04 11:29 AM |
error loading explorer.exe. SHLWAPI.dll | Gary | General | 4 | October 20th 04 04:08 AM |
FAQ: Win98 users: Upgrading to WinXP, IE6, etc. | JM | Improving Performance | 6 | July 26th 04 01:44 PM |
Microsoft Security Bulletin MS04-023--Please Note! | Gary S. Terhune | General | 4 | July 14th 04 04:39 AM |
Please help! Display settings !! | Mitzi | Monitors & Displays | 12 | July 11th 04 05:19 AM |