A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows ME » General
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Epson R200 Printer Error......



 
 
Thread Tools Display Modes
  #1  
Old May 19th 05, 05:08 PM
Heather
external usenet poster
 
Posts: n/a
Default Epson R200 Printer Error......

Hi All......

This is the error I got on startup....the usual one. And my icon in the
tray for checking the printer did not load. Not sure quite what this
is.....but hope I have it plugged in right.....the two pins keep falling out
and it is not screwed in tight.

Cheers....Heather

SPOOL32 caused an invalid page fault in
module SPOOL32.EXE at 016f:00402075.
Registers:
EAX=00000004 CS=016f EIP=00402075 EFLGS=00010283
EBX=00000000 SS=0177 ESP=0086ff84 EBP=00000000
ECX=d66eb830 DS=0177 ESI=bff6ca1e FS=32d7
EDX=bffbb490 ES=0177 EDI=bff8306c GS=0000
Bytes at CS:EIP:
ff 33 55 e8 73 f0 ff ff 89 03 e8 e4 0c 00 00 89
Stack dump:
00000000 00000004 0086ffcc 81e0124c 00000008 81dfa3a0 bff79391 00000000
81e0124c 00000008 81dfa3a0 00000007 0086ffa4 0086fdb4 ffffffff bffb1b20


  #2  
Old May 19th 05, 05:20 PM
Mike M
external usenet poster
 
Posts: n/a
Default

Heather,

And my icon in
the tray for checking the printer did not load.


Did you uncheck on of the registry entries for the printer? If so then it
could have been the tray icon. I don't have a tray icon displaying here
other than when there is a print job printing.

Not clear what you mean about two pins falling out? How are you
connecting your R200? Mine's a USB printer. The only pins I see are
where the lead from the transformer plugs in. Do you mean those pins?
--
Mike


Heather wrote:

Hi All......

This is the error I got on startup....the usual one. And my icon in
the tray for checking the printer did not load. Not sure quite what
this is.....but hope I have it plugged in right.....the two pins keep
falling out and it is not screwed in tight.

Cheers....Heather

SPOOL32 caused an invalid page fault in
module SPOOL32.EXE at 016f:00402075.
Registers:
EAX=00000004 CS=016f EIP=00402075 EFLGS=00010283
EBX=00000000 SS=0177 ESP=0086ff84 EBP=00000000
ECX=d66eb830 DS=0177 ESI=bff6ca1e FS=32d7
EDX=bffbb490 ES=0177 EDI=bff8306c GS=0000
Bytes at CS:EIP:
ff 33 55 e8 73 f0 ff ff 89 03 e8 e4 0c 00 00 89
Stack dump:
00000000 00000004 0086ffcc 81e0124c 00000008 81dfa3a0 bff79391
00000000 81e0124c 00000008 81dfa3a0 00000007 0086ffa4 0086fdb4
ffffffff bffb1b20


  #3  
Old May 19th 05, 05:29 PM
Mike M
external usenet poster
 
Posts: n/a
Default

Did you uncheck on of the
Did you uncheck ONE of the ...
--
Mike


Mike M wrote:

Did you uncheck on of the registry entries for the printer? If so
then it could have been the tray icon. I don't have a tray icon
displaying here other than when there is a print job printing.

Not clear what you mean about two pins falling out? How are you
connecting your R200? Mine's a USB printer. The only pins I see are
where the lead from the transformer plugs in. Do you mean those pins?


  #4  
Old May 19th 05, 06:26 PM
Heather
external usenet poster
 
Posts: n/a
Default


"Mike M" wrote in message
...
Heather,

And my icon in
the tray for checking the printer did not load.


Did you uncheck on of the registry entries for the printer? If so then it
could have been the tray icon. I don't have a tray icon displaying here
other than when there is a print job printing.


Not yet......one has the HKCU ending in Startup and the other doesn't. I
have always had the printer icon in the tray. On right click, it is to
check nozzles and the like. Which entry should I take out of Startup?? The
registry one or the plain jane one.

Not clear what you mean about two pins falling out? How are you
connecting your R200? Mine's a USB printer. The only pins I see are
where the lead from the transformer plugs in. Do you mean those pins?


Oh dear.....(G). I have such a bleepin' mess of cords behind there that I
thought it was the printer....mine is a USB connection same as yours. Have
to pull this out and figure out what the blue connection is with the two
pins in it that you screw tight. Can't seem to get it back right, but will
get Ron to come and hold stuff so I don't send the cpu crashing to the
floor.....it is on top of a 2-drawer file cabinet. Cat fur and cpu's don't
go together, lol.

This spool error was there occasionally from after the try at an XP install
by me and before I unplugged everything to take this over to Willy. So must
be something stupid with the printer......not my plugging stuff back in.

Hope this makes sense......Heather
--
Mike


Heather wrote:

Hi All......

This is the error I got on startup....the usual one. And my icon in
the tray for checking the printer did not load. Not sure quite what
this is.....but hope I have it plugged in right.....the two pins keep
falling out and it is not screwed in tight.

Cheers....Heather

SPOOL32 caused an invalid page fault in
module SPOOL32.EXE at 016f:00402075.
Registers:
EAX=00000004 CS=016f EIP=00402075 EFLGS=00010283
EBX=00000000 SS=0177 ESP=0086ff84 EBP=00000000
ECX=d66eb830 DS=0177 ESI=bff6ca1e FS=32d7
EDX=bffbb490 ES=0177 EDI=bff8306c GS=0000
Bytes at CS:EIP:
ff 33 55 e8 73 f0 ff ff 89 03 e8 e4 0c 00 00 89
Stack dump:
00000000 00000004 0086ffcc 81e0124c 00000008 81dfa3a0 bff79391
00000000 81e0124c 00000008 81dfa3a0 00000007 0086ffa4 0086fdb4
ffffffff bffb1b20




  #5  
Old May 19th 05, 06:42 PM
Mike M
external usenet poster
 
Posts: n/a
Default

I'll try and stick my R200 on my Win Me box later but that box is
unfortunately dead in the water at the moment. Nothing to do with Win Me
but a lot to do with the PC having crashed badly when the power cord got
inadvertently pulled out a couple of days ago. It won't restart at the
moment but I just don't have the time to check it out just now but
hopefully tomorrow sometime.
--
Mike Maltby MS-MVP



Heather wrote:

"Mike M" wrote in message
...
Heather,

And my icon in
the tray for checking the printer did not load.


Did you uncheck on of the registry entries for the printer? If so
then it could have been the tray icon. I don't have a tray icon
displaying here other than when there is a print job printing.


Not yet......one has the HKCU ending in Startup and the other
doesn't. I have always had the printer icon in the tray. On right
click, it is to check nozzles and the like. Which entry should I
take out of Startup?? The registry one or the plain jane one.

Not clear what you mean about two pins falling out? How are you
connecting your R200? Mine's a USB printer. The only pins I see are
where the lead from the transformer plugs in. Do you mean those
pins?


Oh dear.....(G). I have such a bleepin' mess of cords behind there
that I thought it was the printer....mine is a USB connection same as
yours. Have to pull this out and figure out what the blue connection
is with the two pins in it that you screw tight. Can't seem to get
it back right, but will get Ron to come and hold stuff so I don't
send the cpu crashing to the floor.....it is on top of a 2-drawer
file cabinet. Cat fur and cpu's don't go together, lol.

This spool error was there occasionally from after the try at an XP
install by me and before I unplugged everything to take this over to
Willy. So must be something stupid with the printer......not my
plugging stuff back in.

Hope this makes sense......Heather


  #6  
Old May 19th 05, 06:53 PM
Heather
external usenet poster
 
Posts: n/a
Default

Hi Mike......

Not to worry. I unchecked the *plain jane one*......not the HKCU one which
is Per-User Run. The plain jane is Machine Run....which does not mean sweet
*** all to me, grin. (oops, that wasn't the word you guys thought it was,
grin) Anyway, rebooted and no error, but it doesn't happen every time.

Have to head out to another town to pick up my car, so will catch up with
you later. Tried the printer and it worked fine and I STILL have this icon
in the lower tray which says Monitoring Preferences, Check Ink, etc.

Later I will pull all the cords out from the back of the CPU and figure out
which one the blue one is but I think it is attached to a Com Port thingie.
My eyesight is no longer the greatest, so will get a magnifying glass and
double check the *teeny tiny* imprint on the CPU connection.

XX for now.....Heather
"Mike M" wrote in message
...
I'll try and stick my R200 on my Win Me box later but that box is
unfortunately dead in the water at the moment. Nothing to do with Win Me
but a lot to do with the PC having crashed badly when the power cord got
inadvertently pulled out a couple of days ago. It won't restart at the
moment but I just don't have the time to check it out just now but
hopefully tomorrow sometime.
--
Mike Maltby MS-MVP



Heather wrote:

"Mike M" wrote in message
...
Heather,

And my icon in
the tray for checking the printer did not load.

Did you uncheck on of the registry entries for the printer? If so
then it could have been the tray icon. I don't have a tray icon
displaying here other than when there is a print job printing.


Not yet......one has the HKCU ending in Startup and the other
doesn't. I have always had the printer icon in the tray. On right
click, it is to check nozzles and the like. Which entry should I
take out of Startup?? The registry one or the plain jane one.

Not clear what you mean about two pins falling out? How are you
connecting your R200? Mine's a USB printer. The only pins I see are
where the lead from the transformer plugs in. Do you mean those
pins?


Oh dear.....(G). I have such a bleepin' mess of cords behind there
that I thought it was the printer....mine is a USB connection same as
yours. Have to pull this out and figure out what the blue connection
is with the two pins in it that you screw tight. Can't seem to get
it back right, but will get Ron to come and hold stuff so I don't
send the cpu crashing to the floor.....it is on top of a 2-drawer
file cabinet. Cat fur and cpu's don't go together, lol.

This spool error was there occasionally from after the try at an XP
install by me and before I unplugged everything to take this over to
Willy. So must be something stupid with the printer......not my
plugging stuff back in.

Hope this makes sense......Heather




  #8  
Old May 20th 05, 02:02 AM
Heather
external usenet poster
 
Posts: n/a
Default

OK....confused as all get out. But I ran Regedit and Epson is where you
said, but under Run- (dash after it, but not in the plain Run one) in
HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run .

This is the "Registry Per-User" one in Startup.....which ends in HKCU. I
will type it out.....

Registry (Per-User Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series" /M
"Stylus Photo R200" /EF "HKCU"


The one I unchecked just says the following.....
Registry (Machine Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series" /05
"LPT1:" /M "Stylus Photo R200"

Sorry Mike......I don't know much about the Registry and will go back and
recheck the latter one if you think it is wise.

I have also been getting a lot of VSOM errors on shutdown and that is the
next thing to tackle. I may just reinstall both Epson and ZAPro to see if
that cures it. I am really flying blind here. I will ask my ZA questions
in another thread.

Cheers.....Heather

"Mike M" wrote in message
...
Heather,

I thought I had explained in a previous post that the Machine Run entry is
almost certainly an entry in
HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run
--
Mike Maltby MS-MVP



Heather wrote:

Hi Mike......

Not to worry. I unchecked the *plain jane one*......not the HKCU one
which is Per-User Run. The plain jane is Machine Run....which does
not mean sweet *** all to me, grin. (oops, that wasn't the word you
guys thought it was, grin) Anyway, rebooted and no error, but it
doesn't happen every time.

Have to head out to another town to pick up my car, so will catch up
with you later. Tried the printer and it worked fine and I STILL
have this icon in the lower tray which says Monitoring Preferences,
Check Ink, etc.

Later I will pull all the cords out from the back of the CPU and
figure out which one the blue one is but I think it is attached to a
Com Port thingie. My eyesight is no longer the greatest, so will get
a magnifying glass and double check the *teeny tiny* imprint on the
CPU connection.




  #9  
Old May 20th 05, 02:23 AM
Mike M
external usenet poster
 
Posts: n/a
Default

Heather,

Run- means that the item is unchecked in MSConfig.

I don't really want to comment further until I get my Win Me box up and
running and install the R200 but have to admit to being intrigued at
seeing a reference to LPT1: (that is, a parallel port) in the unchecked
HKLM entry.

It's late which is probably why I don't know what the VSOM errors are that
you mention. Perhaps you mean vsmon?

I'll try and post back later tomorrow by which time I hope I'll be able to
check out a Win me box with an R200 installed. At least some sleep might
help.

Cheers,

Mike


Heather wrote:

OK....confused as all get out. But I ran Regedit and Epson is where
you said, but under Run- (dash after it, but not in the plain Run
one) in HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run .

This is the "Registry Per-User" one in Startup.....which ends in
HKCU. I will type it out.....

Registry (Per-User Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series"
/M "Stylus Photo R200" /EF "HKCU"


The one I unchecked just says the following.....
Registry (Machine Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series"
/05 "LPT1:" /M "Stylus Photo R200"

Sorry Mike......I don't know much about the Registry and will go back
and recheck the latter one if you think it is wise.

I have also been getting a lot of VSOM errors on shutdown and that is
the next thing to tackle. I may just reinstall both Epson and ZAPro
to see if that cures it. I am really flying blind here. I will ask
my ZA questions in another thread.


  #10  
Old May 20th 05, 03:17 AM
Heather
external usenet poster
 
Posts: n/a
Default

Thanks, Mike.......I am now trying to digest this. Been dealing with
painters all day and stuff......my head is not into this. Have to go and
clean up the master bedroom coz it is being painted at 8:30 AM tomorrow
(ungodly hour!!).....

Of course I meant Vsmon....drat. (G) I am losing it. I know it is a ZA
error and I have some questions to ask about an upgrade. Seems I can either
use my version 4.5.594.00 with webfiltering as they are not upgrading it any
more.......OR switch to a totally free Security Suite. Blew me away!! I am
not entirely sure I want that on here......you know I usually stay at least
2 or 3 versions behind. Last one was 2.6.xxx, grin.

Talk to you tomorrow.......Heather

"Mike M" wrote in message
...
Heather,

Run- means that the item is unchecked in MSConfig.

I don't really want to comment further until I get my Win Me box up and
running and install the R200 but have to admit to being intrigued at
seeing a reference to LPT1: (that is, a parallel port) in the unchecked
HKLM entry.

It's late which is probably why I don't know what the VSOM errors are that
you mention. Perhaps you mean vsmon?

I'll try and post back later tomorrow by which time I hope I'll be able to
check out a Win me box with an R200 installed. At least some sleep might
help.

Cheers,

Mike


Heather wrote:

OK....confused as all get out. But I ran Regedit and Epson is where
you said, but under Run- (dash after it, but not in the plain Run
one) in HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run .

This is the "Registry Per-User" one in Startup.....which ends in
HKCU. I will type it out.....

Registry (Per-User Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series"
/M "Stylus Photo R200" /EF "HKCU"


The one I unchecked just says the following.....
Registry (Machine Run)
C:\WINDOWS\SYSTEM\E_S4l2H1.EXE /P30 "EPSON Stylus Photo R200 Series"
/05 "LPT1:" /M "Stylus Photo R200"

Sorry Mike......I don't know much about the Registry and will go back
and recheck the latter one if you think it is wise.

I have also been getting a lot of VSOM errors on shutdown and that is
the next thing to tackle. I may just reinstall both Epson and ZAPro
to see if that cures it. I am really flying blind here. I will ask
my ZA questions in another thread.




 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Reinstalling Windows Bill in Co. General 35 April 29th 05 08:29 PM
USB PRINTER not recognized wouldbee General 4 February 17th 05 08:36 PM
Printer Timeout Error Message Jmiskell Printing 0 July 8th 04 06:50 PM
AV software and PC in safe mode Jane New Users 20 July 1st 04 08:57 PM
Spool32.exe error on Windows 98. Shibin John Printing 3 June 7th 04 06:24 AM


All times are GMT +1. The time now is 09:26 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 Win98banter.
The comments are property of their posters.