A Windows 98 & ME forum. Win98banter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » Win98banter forum » Windows 98 » General
Site Map Home Authors List Search Today's Posts Mark Forums Read Web Partners

Any Tapi/Dun/Modem Experts Question



 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old October 29th 05, 06:50 AM
Franc Zabkar
external usenet poster
 
Posts: n/a
Default Any Tapi/Dun/Modem Experts Question

On Tue, 25 Oct 2005 01:00:36 +0000 (UTC), nonewbie
put finger to keyboard and composed:

cannot get dun to work with aztech mdp3880-w(u) modem.

installed latest drivers, install went fine. "more info" reported info
from the modem.

When I try to dialout using dun i get : "error 633- modem is not
installed or configured for dialup, double click on the modems icon in
control panel"

When I do the above, it tries to reinstall the modem drivers,even though
they have already been installed.

Tried on of MS's solutions and rebuilt telephon.ini, still no go. Also
did their registry fix for telephon.ini

tried uninstalling and reinstalling drivers and modem still no problem.
Modem now assigned to com3 IRQ 10

in my Dell dimension bios, there is a section for all the irqs where u
set it to either available or reserved, but I was told that this is only
for non-plug and pray modems and I got a message from windows saying
this is plug and pray modem. IRQ is currently marked available in bios.


Your modem uses a Rockwell/Conexant HCF (controllerless) chipset. It's
not a bad performer, at the very least it uses much less CPU power
than Conexant's softmodems (HSF).

These are Conexant's generic drivers for HCF modems:
http://www.conexant.com/support/files/HCFp_Win9x.zip

This is the entry point for all other drivers:
http://www.conexant.com/support/md_d...ssistance.html

Your modem's properties, commands, and responses are located at this
registry key:

HKEY_LOCAL_MACHINE\System\CurrentControlSet\Servic es\Class\Modem\000n

How does yours look?

If this key has a problem, then check the contents of the modem's INF
file. That's where the setup info comes from.

Can you set up a comms session using HyperTerminal?

Here is a FAQ that may have useful info:
http://www.conexant.com/support/md_faqs.html

IIRC, there is a special procedure to uninstall HCF/HSF drivers.

Here is an excerpt from the FAQ:

================================================== ===================
I would like information on drivers to install for both modem
enumerator and modem.

The installation instructions are packaged with the generic drivers.
Please refer to the readme.txt file for instructions on how to remove
and install the drivers.
================================================== ===================

Here are two other sites that may be useful:
http://www.aztech.com.sg/SAnalog.htm#14
http://www.modemsite.com/56k/rockhcf.asp

-- Franc Zabkar

Please remove one 'i' from my address when replying by email.
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Any Tapi/Dun/Modem Experts Question jt3 General 9 November 2nd 05 01:38 AM
Any Tapi/Dun/Modem Experts Question Ben Myers General 2 October 31st 05 02:06 PM
Any Tapi/Dun/Modem Experts Question glee General 7 October 31st 05 04:35 AM
Any Tapi/Dun/Modem Experts Question poatt General 1 October 28th 05 06:26 PM
Poledit question JohnDeeze General 0 December 6th 04 02:35 AM


All times are GMT +1. The time now is 01:04 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 Win98banter.
The comments are property of their posters.