If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Can't add tcp/ip protocol
I've used an 802.11b PCMCIA card for months with no
problems but now I can't connect to the host because I lost my tcp/ip somehow. When I right click on "Network Neighborhood" and select properties, nothing happens when I click the "add" button after selecting "add" then "protocol" I bought a used notebook and don't have the Windows 98SE install or recovery CD's. I just have what's in the Win98 folder -- tons of .cab files. A pointer to a book or Knowledge Base article would be sufficient. Thanks a lot, Larry |
#2
|
|||
|
|||
PS: Network now "not complete"
When I click on Network in my Control Panel, I get a
dialog box that says "Your network is not complete." I'm running Windows 98SE as a single user. Do I have to somehow log in as a system administrator to install TCP/IP? Thanks again to one and all who post replies. Larry ================================================== ===== -----Original Message----- I've used an 802.11b PCMCIA card for months with no problems but now I can't connect to the host because I lost my tcp/ip somehow. When I right click on "Network Neighborhood" and select properties, nothing happens when I click the "add" button after selecting "add" then "protocol" I bought a used notebook and don't have the Windows 98SE install or recovery CD's. I just have what's in the Win98 folder -- tons of .cab files. A pointer to a book or Knowledge Base article would be sufficient. Thanks a lot, Larry . |
#3
|
|||
|
|||
PS PS: tabs missing from Network in Control Panel
In addition to the dialog box stating that "Your network
is not complete" when I double-click Network in my Control Panel, I am confronted with only the Configuration tab; the Identification and Access Control tabs are missing! What am I now missing? I ran TCP/IP on 802.11b for months and visited countless web sites! Once again, a pointer to a book, article or Knowledge Base entry would be great. I've searched the Knowledge Base extensively and don't find anything about my problem. Thanks much, Larry -----Original Message----- I've used an 802.11b PCMCIA card for months with no problems but now I can't connect to the host because I lost my tcp/ip somehow. When I right click on "Network Neighborhood" and select properties, nothing happens when I click the "add" button after selecting "add" then "protocol" I bought a used notebook and don't have the Windows 98SE install or recovery CD's. I just have what's in the Win98 folder -- tons of .cab files. A pointer to a book or Knowledge Base article would be sufficient. Thanks a lot, Larry . |
#4
|
|||
|
|||
Remove and reinstall DUN and TCP/IP:
http://support.microsoft.com/default...;en-us;Q181599 If that doesn't help, you probably need a winsock repair: http://inetexplorer.mvps.org/data/lsp_fix.htm -- _______________________________________ Sandi - Microsoft MVP since 1999 (IE/OE) http://inetexplorer.mvps.org "Larry Ballard" wrote in message ... I've used an 802.11b PCMCIA card for months with no problems but now I can't connect to the host because I lost my tcp/ip somehow. When I right click on "Network Neighborhood" and select properties, nothing happens when I click the "add" button after selecting "add" then "protocol" I bought a used notebook and don't have the Windows 98SE install or recovery CD's. I just have what's in the Win98 folder -- tons of .cab files. A pointer to a book or Knowledge Base article would be sufficient. Thanks a lot, Larry |
#5
|
|||
|
|||
The problem was apparently not with some .inf files, but
rather with the Windows Registry. I got my TCP/IP stack back by backing up my registry and extracting USER.DAT and SYSTEM.DAT -----Original Message----- I've used an 802.11b PCMCIA card for months with no problems but now I can't connect to the host because I lost my tcp/ip somehow. When I right click on "Network Neighborhood" and select properties, nothing happens when I click the "add" button after selecting "add" then "protocol" I bought a used notebook and don't have the Windows 98SE install or recovery CD's. I just have what's in the Win98 folder -- tons of .cab files. A pointer to a book or Knowledge Base article would be sufficient. Thanks a lot, Larry . |
#6
|
|||
|
|||
The problem was not with any .inf files, but rather with
my Windows Registry (surprise, surprise). I got my TCP/IP stack back immediatlely by backing up my windows registry using regedit in Windows, extracting USER.DAT and SYSTEM.DAT from an old rb00?.cab file in DOS, then booting Windows again. (Set appropriate attributes on the extracted .DAT's and saved the old ones by renaming them, just in case Windows wouldn't boot anymore.) After I restored some of the files mentioned in Q181599, I ran System File Checker and saw that some of the virtual device drivers (.vxd files) I restored per Q181599 were *older* than the ones I had renamed to .dxv files. This caused some problems because my computer's manufacturer had updated several drivers since the last release of my Windows OS (Windows 98SE 4.10.2222 A). Anyway, I've got TCP/IP back and my Network dialog box in the Control Panel now shows Identification and Access Control tabs with *all* appropriate client, server and protocol entries. Hope this helps anyone in the future who may have this problem, and thanks for the guidance. Larry |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TCP/IP problem | Peter | General | 1 | August 12th 04 04:04 AM |
How to tell which protocol (NetBUI or TCP/IP) each Network Neighborhood connection is using | Dave Burton | Networking | 26 | August 8th 04 07:22 AM |
How to tell which protocol (NetBUI or TCP/IP) each Network Neighborhood connection is using | Dave Burton | Networking | 26 | August 8th 04 07:22 AM |
Can't enter IP address in TCP/IP properties | John H. | Networking | 0 | July 12th 04 11:20 AM |
BLA indicates 23 second delay for TCP/IP network | BoB | General | 11 | June 28th 04 09:47 PM |