I have tried reinstalling the drivers. Dell moderator ChrisM has helped me
locate the drivers from the Dell site and I have searched for the proper
drivers using the Service Tag on the Dell site. The Intel graphics card is
part of the Dell motherboard so there is not a problem with loose
connections. The downloaded files are unzipped, placed in folders, the
installation is completed, the computer reboots, but I still have the yellow
exclamation mark. I can go into the driver file details and the File Version
4.13.01.2759 reflects the driver version I downloaded and installed.

I have also tried the drivers from the Intel site. I have not had any luck.

"Jack E Martinelli" wrote in message
...
Susan, if the computer is displaying any video at all, the graphics chip
on
the mainboard is probably not damaged.

I think you should retry to install the latest Intel driver for your
particular video chip. Note that this file is rather old, as this chip is
obsolete now.
See the link from my previous post and retry the updating.

Typically, this involves downloading the install file, eg., to your newly
created folder, C:\Windows\Drivers\Intel\Graphics, and running it, which
will automatically place all the needed driver files in the desired
folders,
usually Windows\System, and Windows\INF. When you reboot, you will be
using
the new video driver, and can configure the video system, as desired,
using
the Display applet. You may see some new features in the applet, due to
the
updated driver. Set the resolution, color depth, and refresh rate to
those
desired. Confirm that the correct monitor driver is installed to enable
all
the monitor's features.

"Patience and persistence" are the key.
--
Jack E. Martinelli 2002-05 MS MVP for Shell/User / DTS
Help us help you: http://www.dts-L.org/goodpost.htm
In Memorium: Alex Nichol
http://www.microsoft.com/windowsxp/e...ts/nichol.mspx
Your cooperation is very appreciated.
------
"Susan" wrote in message
...
Thank you everybody for your suggestions. What is funny is that I never
had
these problems with our other Dell and I have reinstalled Windows ME on
it
about 3 times. It has the same Intel Graphics card but is a different
model
with the Pentium --not a Celeron processor. Hopefully something will
come
up but think I have exhausted this subject on the newsgroup. Even though
I
have not found the answer I always feel that I go away knowing more than
I
did before.

Thanks,
Susan

"Jack E Martinelli" wrote in message
...
Intel® 82810 Graphics Controller
4 downloads on 1 page supported for Windows* Me

http://downloadfinder.intel.com/scri...submit=Go%2 1

Graphics Driver [WIN9XE67.EXE, WIN9XM67.EXE] (4608KB) 6.7
8/23/2002

--
Jack E. Martinelli 2002-05 MS MVP for Shell/User / DTS
Help us help you: http://www.dts-L.org/goodpost.htm
In Memorium: Alex Nichol
http://www.microsoft.com/windowsxp/e...ts/nichol.mspx
Your cooperation is very appreciated.
------
"Mike M" wrote in message
...
The usual reason for a Code 10 error in the Device Manager is due to
the
necessary drivers for the device not being installed. Have you tried
reinstalling or upgrading the graphics drivers for your motherboards
graphics chip? If you are using an add in graphics card did you
perhaps
forget to disable the built-in graphics chip in the motherboard's
bios?

KB 125174 - "Explanation of Error Codes Generated by Device Manager"
(http://support.microsoft.com?kbid=125174) has this to say.

"Code 10
If the device has a "FailReasonString" value in its hardware key, that
string is displayed as the error message. The driver or enumerator
places
this registry string value there. If there is no "FailReasonString" in
the
hardware key, the following generic error message is displayed:

This device is either not present, not working properly, or does not
have
all the drivers installed. (Code 10)

Try upgrading the device drivers for this device.

snip

To resolve this error code, make sure the device is connected to the
computer correctly. For example, make sure all cables are plugged in
fully
and that all adapter cards are properly seated. Follow the suggested
solution button and update the device driver. It may be possible to
remove
the device and redetect it using the Add New Hardware wizard."
--
Mike Maltby MS-MVP



Susan wrote:

What does an error code of 10 mean when one uses msinfo32 and
highlights Problem Devices and the
right pane shows
Device PNP Device
Id Error Code
Intel(r) 82810E Graphics Controller
PCI\VEN_8086&DEV_7125&SUBSYS
10