|
|
4MBit Firmware Hub Problem by
Tom
I have re-installed Windows 98 on an HP Kayak XU800 and
the device manager has a 4MBit Firmware Hub Device that I
cannot seem to find the driver for it. I cannot seem to
get the Network card to work, but it was working fine
prior to the re-installation of Windows 98. Any help with
this matter would...
|
August 17th 04 01:17 AM
by Tom
|
0 |
1,382 |
|
|
What file controls the "delete" function in DOS mode? by
niteowl
Hi all,
I had about 50,000 "*.bak" files on my D: drive, and thought it would
be easiest to remove them in DOS mode, but when I bootup from a bootup
floppy, and type from the "D:\" prompt: "del *.bak" I get a "file
not found" error message.
all the files are named: _S(6digits).bak
I tried...
|
|
4 |
857 |
|
|
HCF Modem by
Don Phillipson
Connection problems persist: e.g. currently
downloading the latest modem manual from
AOpen and speed fell rapidly from 6 Kbs to 2 Kbs . . .
Half the time, first connection simply fails: on
2nd or subsequent attempts, it takes 60 to 120
seconds before good connection is reported.
This does not...
|
|
2 |
1,684 |
|
|
product key by
Sallie
for some reason, one time my computer went crazy and now
it won't restart unless i reinstall windows 98 and I
don't have that stupid number any more!!! what am i
supposed to do????? someone please help me. thanks.
|
|
2 |
1,011 |
|
|
Starting Up by
John
Can someone help me with my laptop? I turned it off and
then on...it asked me to go through a Wizward to input my
product key, which I did successfully. Then, it booted up
but nothing has appeared except my cursor and
wallpaper...what is going on?
|
|
1 |
1,236 |
|
|
Setup problem by
Craig
When I run Windows 98 Setup, it does the scandisk, and
then says "Please wait while setup initializes. Scanning
system Registry.. Copying files needed for windows
setup..." and then goes back to the command prompt
I have an active Fat32 partition of around 39Gb.
I have an Intel P3 650Mhz with...
|
August 16th 04 04:09 AM
by Craig
|
0 |
1,498 |
|
|
mouse disappearance by
i use windows 98se and upon booting up the mouse does not
appear at the desktop what is wrong and how can i correct
plug in is good
|
August 16th 04 01:42 AM
by
|
0 |
779 |
|
|
What's this: "While initializing device NDIS: Windows protection error."? by
Joshua
I just built my first computer, and it works fine: When I
turn it on, fans spin and lights come on, along with the
complementary beeping noise. Everything there is installed
right, I'm sure. But after installing Windows98 fully,
instead of going to my desktop when turning the computer
on, instead...
|
August 15th 04 11:38 PM
by Spajky
|
4 |
2,100 |
|
|
Lost Product Key by
Dave
I tried to restore my computer today. Things went well
until Windows 98 started. I need my Product Key to start
the complete computer. I have no idea where the jacket
is that has the Product Key information. Any ideas?
Lost
|
August 15th 04 11:33 PM
by
|
3 |
973 |
|
|
|
|
2 |
1,337 |
|
|
Still the same blue screen by
Ty
Im still getting a fatal exception 0E error while
checking plug and play devices, Ive restarted almost 8
times and the results are the same. What should I do?
|
August 15th 04 03:59 PM
by glee
|
3 |
1,225 |
|
|
Suppressing Version Conflict Message by
Matthias
Hi,
how can I set the default action of VCM (version Conflict Manger) to "No
Replace"?
The system is updated with everything available and I would not like the
Win98-Setup to overwrite any newer version of the file.
Reg.
Matthias
|
|
0 |
632 |
|
|
start-up a "wiped" drive by
Lucinda
I just bought a 3 yr old dell pentium 3 at a state surplus
that has been wiped.. Can anyone please tell me how to get
this thing to run. The only drive that works right now is
the floppy. I have wind 98 on a bootable cd..It only goes
so far then it stops to a c:\ promt..
|
August 15th 04 05:37 AM
by
|
2 |
928 |
|
|
new desktop by
tryme
Can any one help?
When I rebooted my computer, I have a new desktop with a
lot fewer icons than before. When I try to click on
anything, I get this error message:
"current security settings do not permit active x
controls"
I can't use the computer as it is.
|
August 14th 04 04:05 PM
by tryme
|
0 |
902 |
|
|
Windows 98 SE wont finish setup by
Ty
I formatted my harddrive and started installing windows
98 SE everything goes fine until i get to the final step
after it restarts my computer. When I get to installing
plug or play devices, a blue screen pops up and says A
fatal exception 0E has occured at 0028:FF02847B The
current application...
|
|
2 |
641 |
|
|
start-up by
Dupre
Windows 98 starts up when my telephone rings. How do I
change this setting
|
|
1 |
433 |
|
|
Win 98 upgrading from 95 by
Mike
I was upgrading a friends pc from 95 to 98. Everything
seemed fine until the person thinks they shut down but
switched off before safe message. Now the computer will
not even boot up,just get blank screen. Anyone any ideas
how to get some workable screen to fix it, please? Thanks
|
|
1 |
847 |
|
|
certificate of authenticity by
rick
I had to reinstall Windows 98 on my daughter's computer
using the disc that came with her Packard Bell machine.
Everything was going well until the window asked for a
certificate of authenticity. The disc I was using was
from PB and had no numbers on it and any codes from the
computer purchase are...
|
|
1 |
1,091 |
|
|
windows by
how do i reinstall windows
|
|
1 |
1,401 |
|
|
win98 reinstall by
Vin
I was trying to reinstall win98 in an IBM Aptiva. Starts
out ok then get a message saying have to put in the win98
upgrade. Where can I download it? Thanks in advance.
|
|
1 |
986 |